TPS2052BDGN
Product Specifications
TPS2052BDGN
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2052BDGN from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2052BDGN dual channel 500 mA power distribution switch with active high enables in the 8 pin MSOP PowerPAD body
The TPS2052BDGN is the dual channel 500 mA member of the TPS20xxB family, in the eight pin MSOP body with an exposed thermal pad. Two independent switches share one package, each with its own enable, each with its own fault output, and both can also be ganged so that one enable signal turns both on together. The usual job is a pair of USB ports or a pair of peripheral rails that a host has to be able to disconnect without pulling the main supply down.
The power stage is the same 70 mOhm N channel MOSFET used across the family, one per channel, driven by a shared charge pump. Current limit holds constant current rather than opening the switch, thermal shutdown recovers on its own, and the fault outputs are open drain and active low. What the dual package buys is board area and one shared input capacitor, which on a small board matters more than the pin count.
Key parameters taken from the TPS2052BDGN document
| Rated current | 500 mA per channel, with the two channels able to run at their rating at the same time |
| On resistance | 70 mOhm typical and 135 mOhm maximum over minus 40 to plus 125 C in the D and DGN bodies |
| On resistance at 2.7 V | 75 mOhm typical and 150 mOhm maximum, the price of a weaker gate drive at the bottom of the input range |
| Current limit per channel | 0.75 A minimum, 1 A typical and 1.25 A maximum at 25 C, 0.7 to 1.3 A over the ambient range |
| Current limit with both channels shorted | About 1.5 A typical measured at the input with both outputs grounded, which is the row the vendor publishes for the dual parts |
| Overcurrent trip threshold | 1.55 A minimum and 2 A maximum on the TPS2052B in the DRB body, a separate row from the constant current limit |
| Enable | Active high on both channels, with the active low member of the same rating being the TPS2042B |
| Ganging | The two enables can be tied together so both channels switch at once, which the vendor shows in its own application section |
| Supply current | 75 microamp typical and 95 microamp maximum with the switches on, half a microamp typical and one microamp maximum with them off |
| Turn on and turn off | 3 ms typical turn on and 10 ms typical turn off into 100 microfarad with a 10 Ohm load |
| Fault outputs | One open drain active low pin per channel, asserted in current limit and in thermal shutdown |
| Output discharge | Present on the B family, so both ports are pulled down when their switches are off |
| Body and packing | HVSSOP DGN 8 pins with an exposed pad, 2500 pieces on a 330 mm reel, NIPDAU finish, moisture level 1 unlimited floor life |
| Temperature | Minus 40 to plus 85 C ambient, junction to 125 C |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The two current limit rows in the document have to be read as different things. The per channel row is the constant current level that each switch holds, 0.75 to 1.25 A at room temperature on a 500 mA channel. The other row is measured at the input with both outputs shorted to ground, and it reads about 1.5 A typical, which is not two channels at 0.75 A but a single combined figure under a specific test. A board that needs to know the worst case input current during a double short should work from the per channel window and add the two, not quote the combined row.
The exposed pad is not decorative. Two channels at 500 mA through 135 mOhm maximum dissipate 67 mW in total, which is small, but the same body at the 1 A rating of the higher members reaches 270 mW, and the MSOP without a soldered pad has a thermal resistance near 200 C per watt. The pad has to be connected to a copper area with vias, otherwise the current limit derates in practice even though the data sheet does not say so. On this part, with 67 mW, the risk is low, which is why it is a good first choice for a pair of low current ports.
Ganging the enables is convenient and has one consequence worth knowing. When both channels are tied to one signal, a fault on one channel pulls the input down through its own limit but the other channel keeps running, so the host sees one flag asserted and one port still live. The host has to read both flags rather than assume that one enable means one state. If the product needs both ports to go down together, the fault outputs have to be wired to a gate that pulls the shared enable low.
The supply current figures are per package, not per channel. With both channels on the package draws 75 microamp typical, which is barely more than a single channel part of the same family. The reason is that the charge pump and the reference are shared, so the second channel costs almost nothing in standing current. That is the argument for the dual body on a battery product with two low current ports, where two single parts would double the standing current and the board area.
- Per channel current limit at the hot and cold corners, since the dual rows are wide and the load tolerances overlap them.
- Input current with both outputs shorted, measured rather than taken from the combined row.
- Fault flag behaviour with a single channel in fault, which must not mask the state of the other channel.
- Thermal performance with the exposed pad soldered, since an unsoldered pad derates the part silently.
- Turn off time for each port, where a 10 ms fall through the whole rail range can reset a downstream device.
- Standby current of the package with both switches off, which is the number for a shelf life budget.
Which projects this part fits
This part fits boards with two USB ports that need independent switching and fault reporting, telecom and networking cards with two protected peripheral feeds, instrument front ends where two sensor rails are switched from one host pin pair, and any product where board area is the limit and two single switches would not fit. It is also the practical part when a board already uses the TPS2042B and the enable polarity has to change without a change of footprint.
Questions that come up before a purchase order is released
Are the two channels independent?
Electrically yes, each has its own switch, its own current limit and its own fault output. They share the input rail, the charge pump and the ground. A short on one channel does not turn the other off, so a host that wants both ports down has to act on the flag rather than wait for the part.
Can the outputs be paralleled for 1 A?
No. The two channels limit independently, so the one with the lower on resistance carries more current until it limits, and the pair then delivers less than the sum. If a single 1 A port is needed, the single channel 1 A member of the same family is the part, and it costs less board area than two channels in parallel.
What is the difference between the DGN and the DRB body?
The DGN is the eight pin MSOP with an exposed pad, 2500 pieces on a 330 mm reel. The DRB is a smaller SON body, and the vendor lists the overcurrent trip threshold row for the TPS2052B against the DRB only, so the two bodies are not identical in every published row. If a customer needs that specific behaviour, the body has to be named on the order.
How much input capacitance does the package need?
The vendor application shows 0.1 microfarad at the input and 150 microfarad at each output for a USB style port. The input capacitor supplies the inrush of both ports at plug in, so with two ports the peak input current is the sum of the two inrush currents. A single 0.1 microfarad is thin for that, and most boards place a 1 microfarad ceramic close to the pin as well.
Does the fault output need a pull up per channel?
Yes, each is open drain. One resistor per channel to the host rail, or one resistor per channel to the input rail if the host tolerates a fault report that disappears when the input drops. Do not pull them up to the switched outputs, because then the flags float until the switches turn on.
How SUPERB handles this line
We supply the TPS2052BDGN on original 2500 piece reels with the marking and date code recorded, and we can supply the SOIC body of the same part number when a board has the room. The power management cross reference page lists the dual switches by rating and package, BOM consolidation covers the case where several boards in one product family use different members of the same switch family, and kitting service is how we deliver a mixed set of these parts against one build.