Contact Us

TPS71727DCKR

Brand: Texas Instruments
Texas Instruments TPS71727DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71727DCKR — Power Management & Signal Chain | Superb Automation

TPS71727DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71727DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71727DCKR 2.7 V low noise regulator for an analogue rail

The TPS71727DCKR is the 2.7 V member of the TPS717 family in the five pin SC70 body. It holds 150 mA from a 2.5 V to 6.5 V input with 170 mV of dropout, 70 dB of rejection at 1 kHz and 30 microvolts RMS of noise, and it draws 45 microamps of ground current. A 2.7 V rail is a common analogue supply in instruments that run from a 3.3 V bus: it leaves 600 mV of headroom for a load that has its own internal regulator, and it sits below the 3.0 V where some sensors begin to draw more current.

The 2.7 V row is also used as a pre regulator for a 2.5 V reference, where the extra 200 mV of headroom keeps the reference out of dropout when the 3.3 V bus sags. That arrangement is more robust than feeding the reference from the bus directly, because the bus tolerance and the reference dropout add together in the second case and cancel in the first.

The 1.9 V and 2.7 V rows share one document and one table. Like the rest of the family the part is stable with a 1 microfarad ceramic output, carries a current limit and thermal shutdown, and is specified over minus 40 to plus 125 degrees junction temperature.

Key parameters from the SBVS068I document

Input range2.5 V to 6.5 V
Output2.7 V fixed on this order code
Output current150 mA
Dropout170 mV typical at 150 mA
PSRR70 dB at 1 kHz, 67 dB at 100 kHz, 45 dB at 1 MHz
Noise30 microvolts RMS from 100 Hz to 100 kHz
Ground current45 microamps
Accuracy3 percent worst case over load, line, process and temperature
PackageDCK five pin SC70, 2 mm by 1.25 mm
Order codeTPS71727DCKR, active in the vendor addendum

What changes when the rail is 2.7 V rather than 3.3 V

The dropout budget shrinks. From a 3.3 V bus the part has 600 mV of headroom and needs 170 mV at full load, which leaves 430 mV for the bus tolerance and the trace. A 3.3 V bus at minus 5 percent is 3.135 V, so the margin is 265 mV, still comfortable. On a 3.0 V bus the same arithmetic leaves 130 mV, which is inside the tolerance of the load and is where a board starts to show a sag at the far end of a cable.

The reference divider and the load's own tolerance also shift. Three percent accuracy on 2.7 V is plus or minus 81 mV, which is wider than most loads expect from a rail that is nominally exact, so a load with a 2 percent window has to be checked against the regulator band plus the trace drop rather than against the nominal voltage alone.

Where this part fits

Analogue front ends, sensor bias, instrumentation amplifiers, references and RF blocks that want a rail between 2.5 V and 3 V. On a 3.3 V board the 2.7 V row is the usual way to give an analogue section its own clean rail below the digital one, and on a 5 V board it is the second stage after a converter. Substitution notes between the fixed rows of this family sit under power management cross reference, and the inspection points for a small leaded regulator are in incoming inspection plan.

What to check before a purchase order

Check the headroom at the worst case bus voltage, not at the nominal one. A 3.3 V bus with a 5 percent tolerance and a 150 mA load leaves about 265 mV of margin, and a board with a long trace to the regulator can spend half of that in the copper. If the load is a reference, the margin should be checked against the reference's own dropout, not against zero.

Check the dissipation. From 5 V into 2.7 V at 150 mA the part burns 345 mW, which the SC70 body will carry only with a generous copper area. Most boards that use this row feed it from 3.3 V, where the dissipation is 90 mW and the body is comfortable.

Check the output capacitor and its placement. The family needs 1 microfarad of ceramic at the pin, and a part placed at the far end of a connector does not count, because the trace inductance sits between the loop and the capacitor.

Questions that come up on this part

Can this feed a 2.5 V reference directly? Yes, with 200 mV of headroom at nominal bus, provided the bus tolerance is inside the reference dropout budget.

Is the noise figure the same as the other rows? The document gives the family figure of 30 microvolts RMS, and the fixed voltage does not change it.