Contact Us

TPS73433DDCR

Brand: Texas Instruments
Texas Instruments TPS73433DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73433DDCR — Power Management & Signal Chain | Superb Automation

TPS73433DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73433DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73433DDCR 3.3 V rail with 44 microamp of ground current

The TPS73433DDCR is the 3.3 V fixed member of the TPS734xx family, a 250 mA regulator that runs from 2.7 V to 6.5 V and draws 44 microamp of ground current at no load. The family exists for the case where a rail has to stay alive while the product sleeps. A 3.3 V housekeeping rail feeding a real time clock, a wake comparator and a small memory usually cannot be switched off, and a regulator that draws half a milliamp in that state sets the standby life of the whole product. At 44 microamp the regulator is no longer the largest item in that budget.

What makes the family more than a low current part is that the ac performance does not collapse at that current. Rejection is 60 dB at 1 kHz, output noise is 28 microvolt RMS, and startup is 45 microsecond, so the rail comes up cleanly when the product wakes and does not need a separate sequencing delay. Accuracy is 2 percent over load, line and temperature, and the fixed outputs are factory trimmed by EEPROM between 1.0 V and 4.3 V, which is how a 3.3 V point sits in a family that also covers 1.8 V and 2.5 V without a divider.

Key parameters from the SBVS089F document

Input range2.7 V to 6.5 V
Output3.3 V fixed, adjustable member from 1.25 V to 6.2 V on a 1.208 V reference
Current250 mA continuous
Accuracy1 percent typical on the trimmed output, 2 percent over load, line and temperature
Dropout125 mV typical at 250 mA
Ground current44 microamp typical at no load, 1.0 mA at full load
Rejection60 dB at 1 kHz
Noise28 microvolt RMS with a noise reduction capacitor
Start-up45 microsecond to regulation, no external soft start
Output capacitorStable with 2.0 microfarad ceramic, low ESR
Thermal, DDC bodyJunction to case 90 degrees per watt, junction to ambient 280 low-K and 200 high-K
Thermal, DRV bodyJunction to case 20 degrees per watt, junction to ambient 140 low-K and 65 high-K

The two bodies are not equivalent thermally

The DDC body is a five pin ThinSOT-23 and the DRV body is a six pin two millimetre square SON. On the same JEDEC high-K board the junction to ambient resistance reads 200 degrees per watt for the DDC and 65 for the DRV, a factor of three, and the low-K numbers are 280 against 140. For a 3.3 V rail from 5 V at 250 mA the dissipation is 0.425 W, which is a 85 degree rise in the DDC body and a 28 degree rise in the DRV body. The DDC part therefore cannot hold 250 mA continuously at 5 V in a warm enclosure, and the DRV part can.

A buyer who substitutes one body for the other on the strength of the same order code prefix, without checking the package letter, gets a rail that works on the bench at room temperature and shuts down in the cabinet. The part has thermal shutdown at about 165 degrees with a 145 degree recovery point, so the failure appears as an intermittent drop out rather than a dead board.

Where this part fits

Utility meters, alarm panels, portable instruments and any board with a permanent 3.3 V housekeeping rail use this family because the standby ground current decides the battery life. The cross reference notes for the 3.3 V point across families are under power management cross reference, and the standby current budget we ask suppliers to document is in medical device components.

What to check before a purchase order

Check which body the order code names. The addendum prints the reel row for this string against a WSON body in one column block and against the ThinSOT-23 in another, while the T suffix row is clearly the five pin part. Since the thermal difference between the two bodies is the difference between a working rail and a thermal cycle, the package has to be read from the reel label and not from the code alone.

Check the dropout against the lowest input the product will see. 125 mV typical at 250 mA is a room temperature figure, and the maximum is not published in the same row. For a rail fed from a 3.6 V lithium cell that ends its discharge at 3.0 V, the 3.3 V output is already out of regulation, and no amount of accuracy specification helps.

Questions that come up on this part

Is the noise reduction pin required? No. Without the capacitor the noise rises, and the rejection at low frequency falls slightly, but the regulator is stable and in specification. The pin is there to buy the 28 microvolt figure.

Can the enable pin be left floating? No. The enable input is a defined logic input with a threshold, and a floating pin sits at an undefined level. Tie it to the input when the shutdown function is not used.