Contact Us

TPS16630PWPR

Brand: Texas Instruments
Texas Instruments TPS16630PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS16630PWPR — Power Management & Signal Chain | Superb Automation

TPS16630PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS16630PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS16630PWPR: a 60 V, 6 A eFuse with adjustable current limit in the 20 pin HTSSOP

TPS16630PWPR is a 60 V hot swap controller with an integrated 31 mOhm FET in a HTSSOP (PWP) body of 20 pins. The PWP body is the 20 pin HTSSOP with an exposed pad, 2000 pieces on the large reel in the addendum row. The 30 in the order code is the member without output power limiting: PLIM and the fixed 39 V clamp belong to the TPS16632 and the TPS16637, and a specification that assumes PLIM on a TPS16630 will not be met.

Order code and package

TPS16630PWPRHTSSOP (PWP), 20 pins, 2000 piece large reel, NIPDAU finish, MSL level 2 at 260 C with a one year floor life, -40 to 125 C
TPS16630PWPTthe small reel string; the addendum prints 2000 pieces on a large reel for this row as well, which is unusual for a T suffix and has to be confirmed on the offer
TPS16632same body with output power limiting and the fixed 39 V overvoltage clamp
TPS16637same body with power limiting, configured for higher power rails
RecognitionUL 2367 recognised under file E169910 and certified to IEC 62368-1, which is what makes the part usable as the only protection on a 60 V branch
DocumentSLVSET9G, September 2018 and revised April 2026, so the electrical tables are current against the 2026 revision of the standard

Electrical parameters that decide the application

Input range4.5 V to 60 V operating, 67 V absolute maximum, which is the headroom a 48 V telecom rail plus a transient needs
Pass FET31 mOhm nominal, 26 mOhm to 34.5 mOhm at 25 C and 19 mOhm to 53 mOhm from -40 to 125 C, all measured from IN to OUT at currents between 0.6 A and 6 A
Current limit0.6 A to 6 A set by one resistor, 7 percent accuracy; 30 kOhm gives 0.6 A, 9 kOhm gives 2 A, 4.02 kOhm gives 4.5 A and 3 kOhm gives 6 A
Fast tripthe comparator trips at twice the programmed limit, which is the response that catches a hard short without waiting for the regulated loop
Short circuit45 A of short circuit current capability before the FET is turned off, the figure that decides whether a downstream bulk capacitor is charged through the part or through a resistor
Slew rate controla capacitor on dVdT sets the output ramp with a 2 uA charge current and a gain of 25 V/V, so 100 nF gives a slow, linear rise into a large capacitance
UVLO and OVPboth comparators sit at 1.2 V rising and 1.122 V falling, 2 percent accurate, set by external dividers
Quiescent current1.7 mA maximum while on and 21 uA typical in shutdown, which is what allows the branch to sit in a low current state
Monitor outputsIMON is an analog current output at 6 percent accuracy and PGOOD is an open drain status pin usable to hold a downstream converter off
Fault responsethe MODE pin selects auto-retry or latch off, with an open pin selecting latch
Thermalthe part uses thermal regulation while charging a large capacitive load, so the FET is held at a safe junction temperature instead of being switched off

Family variants and how they differ

TPS16630 against TPS16632the 632 adds output power limiting and the fixed 39 V clamp, which is the pair of features IEC 61010-1 and UL 1310 compliance normally needs
Latch against auto-retrythe MODE pin decides; a latch needs a power cycle or a toggle on SHDN, an auto-retry waits and tries again
Against a discrete hot swapone part with the FET, the sense element and the comparators against a controller plus an external FET and a shunt
Above 6 Athe family stops at 6 A, so a 10 A branch needs a controller with an external FET rather than this part
No reverse current blockingthe body diode conducts in reverse when the output is above the input, which matters on a rail that can be back fed

Points to check before this part goes on a BOM

The resistor on ILIM is the whole current setting, and the document gives four anchor points rather than a curve: 30 kOhm for 0.6 A, 9 kOhm for 2 A, 4.02 kOhm for 4.5 A and 3 kOhm for 6 A. The relationship is not linear, so a 3 A target cannot be reached by halving the 6 A resistor. The 7 percent accuracy applies across the range, and the document warns about parasitic coupling into the ILIM trace, which is the practical reason a limit that measures correctly on a bench fails on a board with a switching converter nearby.

Thermal regulation during startup is the feature that separates this part from a simple switch. Charging a 15 mF load with the dVdT capacitor open, which is the document's own example, would otherwise be a short circuit for hundreds of milliseconds. Instead the FET is held at a junction temperature the die can survive while the output climbs, so the startup is long but the part stays inside its safe operating area without an external resistor.

Latch against auto-retry is a system decision rather than an electrical one. With MODE open the part latches, so a transient that trips the fast comparator takes the branch down until someone toggles SHDN or cycles the input. On an unattended remote site that is the wrong choice, and the same part with the MODE pin strapped for auto-retry keeps trying, which is the right behaviour for a load that may clear its own fault.

The 45 A short circuit figure is what a downstream capacitor sees. A 6 A branch with 1000 uF of bulk capacitance charging from 48 V can pull far more than the programmed limit for a short time, and the fast comparator at twice the limit is what stops it. Sizing the dVdT capacitor for the inrush the source can supply is therefore part of choosing the resistor, not an afterthought.

Setting the two dividers

The UVLO and OVP comparators share the same 1.2 V threshold and the same 2 percent accuracy, so a 36 V undervoltage point and a 60 V overvoltage point come from two divider ratios rather than from two different references. The leakage current of 150 nA maximum on both pins is low enough that a high value divider string does not shift the thresholds, which is why 1 percent resistors dominate the error.

The OVP comparator turns the FET off, it does not clamp, and on the TPS16630 there is no fixed clamp behind it. A 60 V rail that can ring above 67 V needs a transient voltage suppressor in front of the part, because the absolute maximum is a rating and not a protection threshold.

Why the current monitor is the useful pin

IMON sources a current proportional to the load at 6 percent accuracy, and a resistor to ground turns that into a voltage a supervisory ADC can read. That is a real measurement of branch current without a shunt, which is the point: the pass FET is already the sense element.

The same pin is what lets a system distinguish a load that is drawing its rated current from one that is about to trip the limit, so software can shed a load before the hardware removes it.

Where this order code fits

It protects 48 V telecom branches, industrial 24 V and 60 V rails, and any board that has to meet IEC 62368-1 or UL 2367 with a resettable branch instead of a fuse. Teams comparing it with a neighbouring part start from our Incoming Inspection Plan page, and teams replacing a part that has gone end of life start from the Supplier Quality Audit page.

Questions buyers ask

Does the TPS16630 include output power limiting? No. PLIM belongs to the TPS16632 and TPS16637, and the fixed 39 V clamp belongs to the TPS16632 only.

What happens when a large capacitor is charged at startup? The part regulates the FET junction temperature and stretches the ramp instead of tripping the current limit, so a large load capacitance starts slowly rather than faulting.

Is the fault response latched by default? Yes. An open MODE pin selects latch off, so a system that should retry has to strap the pin for auto-retry.

What reel quantity is published? 2000 pieces on a large reel for the PWPR row. The PWPT row in the same addendum also prints 2000 large reel, so confirm the reel size rather than assume 250.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.