Contact Us

TLC352ID

Brand: Texas Instruments
Texas Instruments TLC352ID is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC352ID — Power Management & Signal Chain | Superb Automation

TLC352ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC352ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC352ID: dual differential comparator in an 8 pin SOIC tube, industrial temperature, obsolete order code

TLC352ID is the industrial temperature dual comparator in tube packing, an order code the current addendum lists as obsolete next to its active reel twin in a SOIC body of 8 pins. The I suffix covers minus 40 to 85 C and the plain D suffix is the 8 pin SOIC in tubes. The electrical function is the dual CMOS comparator with open drain outputs, 150 microamps for the pair and a 200 nanosecond response at 10 mV of overdrive. In the packaging addendum this tube code is obsolete, while TLC352IDR on the same die is active on a 2500 piece reel with the same minus 40 to 85 C grade.

Order code and package

Order codeTLC352ID
Functiondual differential comparator, open drain output
PackageSOIC, 8 pins, body code D, tube
Lifecycleobsolete in the current packaging addendum
Active alternativeTLC352IDR, same die and body, 2500 piece reel
Supply range2.7 to 16 V, 18 V absolute maximum
Supply current150 microamps typical, 300 maximum at 5 V
Response time200 nanoseconds at 10 mV overdrive, 100 at 100 mV
Input offset voltage1 mV typical, 5 mV maximum at 25 C, 7 over the range
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Temperature rangeminus 40 to 85 C, I suffix
DatasheetSLCS016B, revision of June 2025

Electrical parameters that decide the application

Input offset voltage1 mV typical, 5 mV maximum at 25 C, 7 mV over the range
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Input offset current1 picoamp typical
Common mode range0 to VDD minus 1 V, VDD minus 1.5 V over temperature
Low output level150 mV typical, 400 maximum at 4 mA, 700 over temperature
Low level output current6 mA typical, 16 mA maximum
Supply current at 2.7 V65 microamps typical, 150 maximum
Response at 10 mV overdrive200 nanoseconds
Response at 100 mV overdrive100 nanoseconds
Input resistance10 to the twelfth ohm typical
Output leakage0.1 nanoamps typical in the off state
Electrostatic rating2000 V human body model

Points to check before this part goes on a BOM

The industrial suffix adds 2 mV to the full range offset, from 6.5 to 7 mV, over a span that is 70 degrees wider than the commercial part. The 25 C limit stays at 5 mV, so a board trimmed at room temperature keeps its accuracy and only the worst case drift changes.

Almost all of the industrial leakage story is at the cold end for offset and at the hot end for bias current. At minus 40 C the offset shifts by about 1 microvolt per degree from its 25 C value, while the bias current falls rather than rises; at 85 C the bias current is the term that grows and the offset is comparatively stable.

The tube packing is obsolete on this code, so a last time buy is the practical route for a repair line. The reel code is the same die in the same body and does not need a circuit change, only a packing change on the BOM.

Mixing this part with an LM393 on the same board is common in older equipment, and the two are pin compatible, but the input bias current differs by six orders of magnitude. A high impedance divider that worked with the CMOS part and then receives a bipolar part during a repair will read a different threshold.

At 2.7 V the pair draws 65 microamps typical, and the common mode window becomes 0 to 1.2 V. A 2.5 V reference threshold is outside that window on a 2.7 V rail, so a low voltage board has to sense a divided version of the rail rather than the rail itself.

The output is open drain with a 16 mA maximum sink, and the low level is 400 mV at 4 mA. A pull-up to a 12 V rail is allowed because the output stands off the full 18 V supply, which is how the part drives a 12 V relay driver from a 3 V logic rail.

Tube packing also changes the assembly route: the parts are hand loaded or fed from a tray adapter, which is why a repair line is the typical user of this code. The 2500 piece reel code is the same part and the same marking, and moving to it costs a feeder setup rather than a board revision.

Where this order code fits

Industrial boards released before the reel code became standard: outdoor sensor units, pump and valve controllers, and power supplies that run in an unheated cabinet where the ambient drops below zero. The minus 40 C floor is the reason to hold this grade rather than the commercial one, and the function is unchanged from the commercial part. Boards comparing it with a neighbouring part start from our Obsolete Part Cross Reference Hub page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is this part still produced? The tube packed order code is listed as obsolete in the current addendum. TLC352IDR is the active industrial code with the same die and the same temperature range.

What changes with the I grade? The temperature range from minus 40 to 85 C and the full range offset limit of 7 mV. The 25 C limits and the response times are unchanged.

Can the output pull up to 12 V? Yes. The output is an open drain transistor that stands off the full supply, so the pull-up can go to 12 V while the comparator runs from 3 V, provided the sink current stays inside 16 mA.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.