AD8604ARZ-REEL7
Product Specifications
AD8604ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8604ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8604ARZ-REEL7: a Quad Rail to Rail Amplifier with 500 microvolts of Offset
What this part is
The AD8604 is a quad operational amplifier with rail to rail inputs and outputs, a maximum offset voltage of 500 microvolts, 8 megahertz of bandwidth and 750 microamps of supply current per amplifier, specified on a single supply from 2.7 V to 5.5 V. The offset is achieved by a trimming technique the vendor calls DigiTrim, which adjusts the die after packaging rather than trimming a resistor during wafer processing, and the result is a part that holds a low offset without the cost of a laser trim step.
The input stage handles signals at both rails without phase reversal, the output swings to within a few millivolts of each rail, and the input currents are low enough that a high impedance source can drive it directly. The temperature range is minus 40 to plus 125 degrees C, which is wider than most parts in this class. Bodies are a 14 lead small outline, a 14 lead thin small outline and a 16 lead QSOP. Applications are portable audio, headsets, barcode scanners, portable instruments, power amplifier control loops and multipole active filters.
Published figures that matter to a buyer
| Channels | 4 |
| Input and output range | rail to rail on both |
| Offset voltage | 500 microvolts maximum |
| Supply range | 2.7 V to 5.5 V single |
| Supply current | 750 microamps per amplifier |
| Bandwidth | 8 megahertz |
| Slew rate | 5 volts per microsecond |
| Phase reversal | none at either rail |
| Stability | unity gain stable |
| Temperature | minus 40 to plus 125 degrees C |
| Bodies | 14 lead small outline, 14 lead thin small outline, 16 lead QSOP |
| Grade option | D grades trade dc precision for price |
Where the headline numbers stop
Five hundred microvolts is 6.55 counts of a 16 bit converter on a 5 V span and 0.16 of a 12 bit count, so the part is a 12 bit amplifier with margin and a 16 bit amplifier only at low gain. The drift term is not quoted in the summary, which means a 16 bit budget cannot be closed from the front page; the data sheet table is where that number lives, and it is the number that decides whether a 500 microvolt offset survives a cabinet that runs at 70 degrees C.
Eight megahertz at unity gain becomes 80 kilohertz at a gain of 100, which is the figure that matters in an instrumentation stage. The slew rate limits the large signal case further: 5 volts per microsecond at a 5 volt peak to peak output is 318 kilohertz of full power bandwidth, so a 3 V peak to peak signal at 100 kilohertz is close to the limit already. Audio and filter applications listed by the vendor sit inside those limits; a fast pulse path does not.
Four amplifiers at 750 microamps each is 3 milliamps, which at 5 V is 15 milliwatts for the package. That is a modest number and it is also four times the current of a single amplifier, which is the trade a quad makes: one package, one set of decoupling capacitors and four times the quiescent current. The D grade exists precisely because some of those four channels do not need the offset, and mixing grades on one board is a normal way to take cost out.
Applications where it fits
- Multipole active filters where four matched amplifiers sit in one package.
- Portable instrument front ends that need rail to rail swing from a single cell rail.
- Buffers for converters and reference dividers on a 3.3 V board.
- Audio and headset amplifiers where a 5 V rail is the only supply.
- Sensor interfaces with moderate impedance where 500 microvolts of offset is acceptable.
Two questions buyers ask
Is the D grade a drop in for the A grade? Same die, same pinout, lower dc precision and a lower price, so the footprint is shared. Whether it can be substituted is a question about the channel that uses it: a filter stage that only needs the offset to stay inside a feedback loop will not notice, and a dc instrumentation channel will.
Does rail to rail input mean the inputs can sit at either supply? The input stage is specified for rail to rail operation and the part has no phase reversal at the rails, which is the property that matters when a signal can exceed the common mode range during a transient. It is not a licence to apply a voltage outside the supply rails: the absolute maximum ratings still apply, and a fault above the positive rail is a fault.
Sourcing notes and next step
AD8604ARZ-REEL7 is the 14 lead small outline in tape and reel, with the RZ marking the body; the thin small outline and the QSOP are separate order codes with separate footprints. Because the family spans single, dual and quad in different bodies, the family name alone does not identify a line, and the A and D grades differ in a field that a bill of materials does not always show. The analog and mixed signal IC family page lists the amplifier line, the amplifier cross reference page sets out the comparison fields, and the medical device components page covers the traceability a medical build expects.
Request Quote — In Stock, 100% New & Original, Full Warranty