ADM3490EARZ-REEL7
Product Specifications
ADM3490EARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM3490EARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADM3490EARZ-REEL7: a full duplex 3.3 V RS-485 transceiver with 15 kV ESD protection
What this order code is
ADM3490EARZ-REEL7 is a 3.3 V differential line transceiver for RS-485 and RS-422 buses, in the full duplex configuration, rated at 12 Mbps. The E in the family name is the ESD grade: plus or minus 15 kV on the RS-485 input and output pins, which is the number that decides whether a field port survives a cable being plugged in while the board is live.
Full duplex means the driver and the receiver have separate pins, so four wires leave the package and a node can transmit and receive at the same time. This member has no driver enable and no receiver enable, which is the difference against the ADM3491E in the same family: the ADM3490E is always driving and always listening, so it belongs at the end of a point to point or a four wire multidrop link rather than on a two wire bus where the driver has to be tri-stated. The receiver input impedance is 12 kilohms, which allows 32 transceivers on the bus. Fail-safe behaviour holds the receiver output high when the inputs are open, the outputs go high impedance when the part is unpowered, and thermal shutdown plus short circuit protection are both present. The pinout follows the industry 75176 arrangement in the 8-lead SOIC body.
Parameters as published
| Item | Value |
|---|---|
| Supply | 3.3 V |
| Standard | TIA/EIA RS-485 and RS-422 |
| Data rate | 12 Mbps |
| Duplex | full duplex, separate driver and receiver pins |
| ESD on bus pins | plus or minus 15 kV |
| Nodes on the bus | 32, receiver input 12 kilohms |
| Common mode input range | minus 7 V to plus 12 V |
| Receiver fail-safe | output high on open inputs |
| Outputs when unpowered | high impedance |
| Protection | thermal shutdown, short circuit |
| Pinout | industry standard 75176 |
| Package | 8-lead SOIC, narrow body |
Numbers that decide the application
At 12 Mbps a bit is 83.3 ns. The 8 ns of driver skew quoted for the family is 9.6 percent of a bit, which is the margin that has to cover cable skew and receiver threshold variation as well, so a 12 Mbps link assumes a short, properly terminated pair. A 120 ohm termination at each end, 32 nodes of 12 kilohms in parallel giving 375 ohms of load, and a stub length that stays under a fraction of the electrical length of the bit are the three physical conditions the number depends on.
The plus or minus 15 kV figure is an ESD rating, not a sustained fault rating. It describes a human body model discharge event and says nothing about a 24 V miswire or a ground potential difference between buildings, which is what the minus 7 V to plus 12 V common mode range covers. Boards that see both often add external transient protection, and the internal rating is then a second line rather than the only one.
Full duplex costs two extra wires and two extra pins. On a two wire bus the driver must be tri-stated while receiving, and this part cannot do that because it has no enable pin. Using the ADM3490E where the ADM3491E was intended produces a bus that two nodes drive at once, which is a fault that shows up as random characters rather than as a clean failure. The check is the pin count and the presence of the enable pins, and it belongs in the incoming inspection, not in the debug session.
Selection and cross reference notes
The family splits three ways: half duplex with enables, full duplex without enables, and full duplex with enables. The 12 Mbps rate appears on several members, so rate alone does not identify the part. The ESD grade is a separate suffix, and a non-E member in the same package will fit the land pattern and fail the field test.
For a drop-in comparison, the fields to match in order are duplex configuration, enable pins, data rate, ESD grade and pinout. A part that matches on the first four but not the fifth is a board revision. A part that matches on all five and differs only in temperature grade is a procurement decision, and that is the case where a second source is genuinely low risk.
Where it fits
Industrial process control, telecom equipment, HVAC controllers and low power RS-485 links are the vendor's applications. The four wire arrangement suits point to point links between a controller and a remote node, and full duplex is what allows a protocol to acknowledge while data is still arriving. The 3.3 V supply keeps it on the same rail as the microcontroller, which removes a level shifter. Buyers comparing interface parts can start at the analog and mixed signal category page, and teams verifying a replacement against an existing socket usually work from the drop-in replacement verification page.
Buying notes
The code reads as family, ESD grade, temperature and body: E is the 15 kV grade, ARZ is the 8-lead SOIC, REEL7 is the reel. Ordering by family name alone will get a half duplex part or a non-E grade, and both fit the same footprint. Because the ESD rating is the reason most buyers choose this line, the grade field is the one to verify on the label.
Sourcing notes and next step
Where the exact code is short, the answer depends on whether the board uses the enable pins and whether the ESD grade is a qualification requirement. We check both before proposing anything. Send the codes, quantities and the target date through the second source page and we will come back with availability and, where a substitute exists, exactly which fields differ.
ADM3490EARZ-REEL7 on a loaded bus: 32 nodes and two terminators come to 51.7 ohm, and that sets the drive current
The receiver input impedance is 12 kohm, which is what allows 32 nodes: 32 of them in parallel give 375 ohm. Two 120 ohm terminators, one at each end of the pair, give 60 ohm, and 60 ohm in parallel with 375 ohm is 51.7 ohm of differential load. A driver that has to reach 1.5 V of differential output must therefore deliver 29 mA into the pair, which is the number the driver's output stage is sized for and the reason a full 32 node bus is a load specification rather than a node count. Reducing the bus to 8 nodes raises the parallel input resistance to 1.5 kohm and the total load to 57.7 ohm, a 12 percent easing.
Bit time, skew and how much cable fits in one bit
At 12 Mbps a bit is 83.3 ns, and the published 8 ns of driver skew is 9.6 percent of it. Cable delays about 5 ns per metre, so one bit is 16.7 m of cable, and a stub that stays under a tenth of a bit is 1.67 m. The skew, the cable's own delay and the receiver's threshold variation all come out of the same 83.3 ns, which is why the 12 Mbps figure belongs to a short, properly terminated pair and not to a long field run. At 1 Mbps the bit is 833 ns and the same 8 ns of skew is one percent, so the same cable carries the same distance more comfortably at the lower rate.
No enables means the part has a fixed place in the network
This member has no driver enable and no receiver enable: it always drives and always listens. That is correct in a four wire full duplex link, where one node owns the transmit pair and never shares it, and it is a bus fault in a two wire half duplex arrangement, where a second always-on driver fights the first and the symptom is random characters rather than a clean failure. The sibling with the enable pins is the member to use where the bus is shared, and the two are the same footprint with different functions.
ESD rating and the fault it does not cover
Plus or minus 15 kV on the bus pins is a human body model rating for a connector being touched or plugged in while the board is live. It says nothing about a 24 V miswire, a ground potential difference between buildings or a sustained fault, which is what the minus 7 V to plus 12 V common mode range covers. A port that has to survive a miswire needs series resistance, a clamp or isolation in addition to the ESD rating, and quoting the 15 kV as though it were a fault rating is the most common misreading of this family.
| Nodes on the bus | Parallel input resistance | With two 120 ohm terminators | Current for 1.5 V differential |
|---|---|---|---|
| 8 | 1.5 kohm | 57.7 ohm | 26.0 mA |
| 16 | 750 ohm | 55.6 ohm | 27.0 mA |
| 32 | 375 ohm | 51.7 ohm | 29.0 mA |
| 32, unterminated | 375 ohm | 375 ohm | 4.0 mA, and reflections |
Field bus transceiver choices are compared on CAN bus transceiver selection, the substitution checks are on how to verify a drop in replacement, and the consolidated order route is on one stop BOM sourcing.
Request Quote — In Stock, 100% New & Original, Full Warranty