Contact Us

TL3116CD

Brand: Texas Instruments
Texas Instruments TL3116CD is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL3116CD — Power Management & Signal Chain | Superb Automation

TL3116CD

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL3116CD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL3116CD: ultra fast comparator with a latch and complementary outputs in an 8 pin SOIC body

TL3116CD is a single voltage comparator that turns a millivolt event into a logic edge in about ten nanoseconds from one 5 V rail, and holds that decision on a latch in a SOIC body of 8 pins. The D suffix is the narrow 8 pin SOIC, and the C suffix fixes the temperature range at 0 to 70 C. The die runs from a single 5 V rail or from plus and minus 5 V, the two outputs are complementary, and the LATCH ENABLE pin freezes both of them within 3.4 nanoseconds of setup, which is how a 2 nanosecond pulse survives long enough to reach a capture register. Output current is 20 mA absolute, and the body dissipates 725 mW at 25 C, derating at 5.8 mW per degree to 464 mW at 70 C.

Order code and package

Order codeTL3116CD
Functionsingle voltage comparator, complementary outputs, latch
PackageSOIC, 8 pins, body code D
Supplysingle 5 V or plus and minus 5 V, 7 V absolute maximum
Output currentplus or minus 20 mA absolute maximum
Response time9.9 nanoseconds typical, 12 maximum at 5 mV overdrive
Latch setup time3.4 nanoseconds
Supply current12.7 mA typical, 14.7 maximum on the positive rail
Dissipation725 mW at 25 C, 464 mW at 70 C, D body
Temperature range0 to 70 C, C suffix
Second sourcepin for pin functional replacement for the LT1116
DatasheetSLCS132C, revision of May 1997

Electrical parameters that decide the application

Input offset voltage0.5 mV typical, 3.5 mV maximum at 25 C and over the full range
Offset driftminus 2.5 microvolts per degree typical
Input bias current0.7 microamps typical, 1.1 maximum, 1.5 over temperature
Input offset current0.1 microamps typical, 0.3 maximum
Common mode rangeminus 5 to plus 2.5 V on plus and minus 5 V, 0 to 2.5 V on a 5 V rail
Common mode rejection75 dB minimum, 100 dB typical
Supply rejection60 dB on the positive rail, 80 dB on the negative rail
Low output level400 mV at 4 mA, 750 mV at 10 mA
High output level3.9 V at 1 mA, 3.8 V at 10 mA
Propagation delay8.2 nanoseconds typical, 13.7 maximum over the full range
Pulse skew0.5 nanoseconds between the two edges
Latch input0.8 V low, 2 V high, 24 to 45 microamps at 2 V

Points to check before this part goes on a BOM

The 12 nanosecond figure is measured with 5 mV of overdrive, and the part carries 3.5 mV of offset. The data sheet says it directly: at low overdrive the offset adds to the overdrive, so a 5 mV step against a 3.5 mV offset leaves 1.5 mV of real drive and the delay stretches toward the 13.7 nanosecond full range limit. An application that needs 10 nanoseconds has to present 20 mV or more.

The positive rail draws 12.7 mA typical and 14.7 mA maximum while the negative rail draws 2.6 to 3 mA, so a plus and minus 5 V board burns about 150 mW before any output current. The D body is rated 725 mW at 25 C and only 464 mW at 70 C, and 20 mA into a 50 ohm load adds 200 mW, which is why the load has to enter the thermal sum and not just the electrical one.

Output levels are TTL shaped but not TTL guaranteed at any current. The low level is 400 mV at a 4 mA sink and 750 mV at 10 mA against an 800 mV threshold, so 10 mA is the last usable sink and the 20 mA the absolute maximum allows is already outside the logic guarantee.

The input common mode window stops 2.5 V below the positive rail. On a single 5 V supply the input works from 0 to 2.5 V, so a signal that swings to the rail is outside the window even though the part is sold as a 5 V comparator. On plus and minus 5 V the window is minus 5 to plus 2.5 V, which is enough for a ground referenced bipolar signal.

Bias current of 1.1 microamps is large next to 0.5 mV of offset. Into a 10 kohm source it becomes 11 mV of error, twenty two times the offset, and into 1 kohm it is 1.1 mV. A low impedance divider or a buffered reference keeps the precision the offset grade was bought for; a 100 kohm ladder in front of this comparator throws it away.

The latch pin is not a logic input with a defined idle state. It draws 24 to 45 microamps when held at 2 V and 10 microamps at ground, and both outputs respond within 3.4 nanoseconds of setup, so an uncommitted latch node captures noise. A 1 kohm resistor to ground is the usual way to keep the comparator transparent when latching is not wanted.

Where this order code fits

This part belongs wherever an analogue event has to become a logic edge faster than a logic gate can manage: peak detection in ultrasound front ends, zero crossing and threshold detection in test instruments, pulse width discriminators, and line receivers that must reject a slow ramp. Radar and radio boards use it to time the arrival of a video pulse, and production fixtures use the latch to hold one short event for the capture register. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the C grade change the timing or only the temperature? Only the temperature. The 12 nanosecond maximum at 5 mV overdrive and the 13.7 nanosecond full range limit come from the same test on both grades, the C grade is specified from 0 to 70 C and the I grade from minus 40 to 85 C, which moves the worst case by about a nanosecond.

Can the output drive a 50 ohm cable directly? No. 20 mA into 50 ohm is 1 V and the low level is already 750 mV at 10 mA, so a 50 ohm load leaves no TTL margin. A follower stage or a 1 kohm load keeps the levels inside the table.

What replaces the LT1116 on an existing board? The TL3116 is the pin for pin functional replacement with the same 8 pinout and the same latch function, and it draws less supply current. The offset grade still has to be compared at the overdrive the board actually uses.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.