TPS54521RHLR
Product Specifications
TPS54521RHLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54521RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54521RHLR 17 V input 5 A buck with a split power rail
The TPS54521RHLR is a 5 A synchronous step down converter that runs from 4.5 V to 17 V on the control input and from 1.6 V to 17 V on the power input, which is what the vendor calls a split rail. The two pins being separate means the power stage can be fed from a 12 V bus while the control circuitry runs from the 5 V rail that is already alive, so the converter keeps regulating when the 12 V bus sags. Both switches are integrated, 57 milliohm high side and 50 milliohm low side, in a 14 pin 3.5 mm by 3.5 mm QFN with a thermal pad.
The current mode loop is compensated externally on COMP, the reference is 0.8 V with a 0.776 V to 0.824 V window, and the switching frequency is set by a resistor on RT between 200 kHz and 900 kHz. A 100 k resistor gives 480 kHz typical, which is the value most reference circuits use because it keeps the inductor near 1.5 microhenry at 5 A while the switching loss stays modest.
The SS/TR pin controls the output ramp and can be driven from a second rail for tracking, and the open drain PWRGD pin gives a hardware indication of a valid output without a bus. Enable and power good together are enough to sequence several rails in a fixed order with no controller.
Key parameters from the SLVS981C document
| Input range | 4.5 V to 17 V on VIN, 1.6 V to 17 V on PVIN, with an internal UVLO rising between 4.0 V and 4.5 V and 150 mV of hysteresis |
| Output current | 5 A continuous from a 57 milliohm high side switch, 95 milliohm maximum, and a 50 milliohm low side switch, 82 milliohm maximum, both at 12 V |
| Reference | 0.8 V with a 0.776 V to 0.824 V window over 0 to 5 A load |
| Switching frequency | 200 kHz to 900 kHz in RT mode, 100 k giving 400 kHz minimum, 480 kHz typical and 560 kHz maximum, 240 k giving 200 kHz and 53 k giving 900 kHz |
| Current limit | High side threshold 7 A minimum and 9 A typical, low side sourcing 6 A to 8 A, low side sinking 1 A to 2.6 A |
| Hiccup timing | 512 cycles of wait before hiccup is triggered and 16384 cycles before the retry, which is about 1 ms and 34 ms at 480 kHz |
| Quiescent current | 2 microamp typical and 5 microamp maximum in shutdown with EN low |
| Orderable body | VQFN RHL, 14 pins, 3.5 mm by 3.5 mm, 3000 pieces on a large reel and 250 on a small reel at moisture level 2 |
Why the split rail is more than a datasheet feature
In a system with a 12 V bus and a 5 V standby rail, the converter that makes the 3.3 V housekeeping supply is usually fed from the 12 V bus. When that bus dips during a load transient or a battery changeover, the converter loses headroom and the output follows the input down. Feeding VIN from the 5 V rail keeps the control loop and the driver alive through the dip, so the 3.3 V output holds until the input to PVIN itself falls below regulation.
The catch is sequencing: the control rail has to be present before the part is enabled, and a board that brings up PVIN first draws no current because the part stays in UVLO. That is why the reference circuits show the 5 V rail feeding VIN and the enable divider taken from the same 5 V, not from the 12 V bus.
Protection and the PWRGD pin
Cycle by cycle current limiting on the high side is backed by a low side sourcing limit that stops current runaway and a low side sinking limit that turns the low side switch off on reverse current. A persistent fault triggers hiccup mode with a fixed wait and a fixed retry, 512 and 16384 cycles, so the retry duty is around 3 per cent and the average current into a short stays small.
PWRGD is open drain and deasserts when the output falls out of regulation, which gives the downstream logic a clean reset without a supervisor. Thermal shutdown disables the switches when the die exceeds its threshold and releases them after hysteresis, so a supply that restarts by itself under load is telling you the thermal path is short of copper.
Where this part fits
Set top boxes, cable modems, industrial controllers and telecom line cards with a 12 V bus all need a 5 A rail for memory or logic, and the split rail makes the part usable where that rail has to ride through input dips. The 3.5 mm QFN with a thermal pad fits behind a connector where a larger package would not.
For a sourcing team the family question is what replaces it when the reel is short: a converter with the same 0.8 V reference and the same 5 A rating but without the split rail can often be used where the rails are tied together, and that trade is set out in power management cross reference and pin to pin cross reference.
What to check before a purchase order
The first field is the package, RHL being the 14 pin QFN, since the same family has been published in other bodies over the years. The second is the reel row, 3000 on the large reel and 250 on the small one. The third is the revision letter in the catalogue string, because the addendum lists a .B row and a plain row for this body and the two are not the same silicon.
Our desk checks those three against the customer bill of materials and, when only the plain row is stocked, says so rather than shipping a reel that looks the same. See component lead time solutions and BOM shortage recovery.