TPS54335ADDAR
Product Specifications
TPS54335ADDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54335ADDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54335ADDAR 28 V input 3 A synchronous buck for 12 V and 24 V housekeeping rails
The TPS54335ADDAR is the adjustable frequency member of the TPS5433xA family, a synchronous step down converter that takes 4.5 V to 28 V in and delivers 3 A continuous. Both power switches are inside the body, 128 milliohm on the high side and 84 milliohm on the low side, so the circuit needs no external catch diode and the board area around the inductor stays free of a second heat source. The body is the 8 pin SO PowerPAD, 4.89 mm by 3.90 mm, with the exposed pad carrying the ground return and the heat.
This is the part a 24 V industrial rail or a 12 V telecom bus uses to make its 5 V or 3.3 V housekeeping supply. The input window covers both buses with margin for a 10 per cent transient, and the frequency is set by one resistor on RT anywhere from 50 kHz to 1.5 MHz. An engineer choosing 480 kHz at 100 k on RT keeps the inductor small without pushing switching loss into the FETs, and a choice of 300 kHz trades board area for efficiency at 3 A.
The reference is 0.8 V with 0.8 per cent accuracy at 25 degrees and 1.5 per cent over temperature, which is what sets the output tolerance at the bottom of the divider. A 3.3 V rail from a 24 V input runs at a 13.8 per cent duty, and the 94 ns minimum on time is comfortable at that duty and still workable at a 5 V to 1.2 V conversion where the duty falls to 24 per cent of a 480 kHz period.
Key parameters from the SLVSCD5D document
| Input range | 4.5 V to 28 V operating, 30 V absolute maximum on VIN, so a 24 V bus with load dump margin stays inside the rating |
| Output current | 3 A continuous, 0.8 V to 24 V output window, with the low end set by the 0.8 V reference |
| Power switches | 128 milliohm high side and 84 milliohm low side, both quoted at 12 V input on the current silicon |
| Switching frequency | 50 kHz to 1.5 MHz set by a resistor on RT, with 100 k giving 384 kHz minimum, 480 kHz typical and 576 kHz maximum |
| Reference | 0.8 V, 0.7936 V to 0.8064 V at 25 degrees, 1.5 per cent over the full junction range |
| Quiescent current | 310 microamp typical and 800 microamp maximum non switching, 2 microamp typical and 10 microamp maximum in shutdown |
| Undervoltage lockout | Rising threshold 4 V minimum and 4.5 V maximum, with 180 mV to 400 mV of hysteresis |
| Timing limits | Minimum on time 94 ns typical and 145 ns maximum measured at 2 A on the PH pin |
Where the adjustable version differs from the fixed one
The TPS54335A and the TPS54336A share the body, the pinout and the power stage, and differ in two places. The TPS54335A has a 2 ms internal soft start and brings the RT pin out so the frequency is set externally. The TPS54336A replaces RT with SS, keeps the frequency fixed at 340 kHz, and lets the ramp be set by a capacitor, with a 2.3 microamp charge current into that capacitor. The soft start pin also overrides the internal reference, which is how a rail is made to track a second rail in a sequenced system.
The practical consequence is that a board already laid out for one member accepts the other on the same pads, since the DDA body is identical on both, but the function of pin 8 changes. A part swapped without noticing that turns the frequency setting resistor into a soft start capacitor, and the converter starts at 340 kHz with a ramp set by whatever sits on that node. This is the single most common mix up in this family and it is worth a marking check on every incoming reel.
Protection behaviour worth knowing before a fault
Current limiting is cycle by cycle on the high side and is backed by a low side sourcing limit that stops the current running away when the inductor saturates, and by a low side sinking limit that turns the low side FET off when reverse current flows back from the output. A persistent overcurrent trips hiccup mode: the part stops switching, waits for the internal hiccup time of 2 ms, and retries. A shorted output therefore ticks instead of cooking the FET, which is what a field failure looks like from the outside.
Thermal shutdown sits between 160 and 175 degrees with 10 degrees of hysteresis, and the overvoltage transition protection stops the high side from switching when the output is pulled above regulation. Both events clear themselves, so a supply that appears to restart on its own at high ambient is usually telling you that the thermal path, not the load, is the problem.
Where this part fits
A 3 A converter at 28 V input covers the housekeeping rail of an industrial control cabinet, the standby supply of a set top box or a router, the bias rail of an audio amplifier, and the auxiliary output of a battery charger. The 84 milliohm low side switch is the reason the part holds efficiency at light load together with pulse skipping, and the monotonic start into a pre-biased output matters when a second rail is already alive at power up. For boards in this class the sourcing question is rarely the part itself and usually the reel behind it, which is where power management cross reference and one stop BOM sourcing come in.
What to check before a purchase order
Three fields decide whether a quoted reel is the right one. The first is the suffix: DDA is the SO PowerPAD body and DRC is the 10 pin VSON, and the two are not interchangeable on a board that was routed for the other. The second is the A suffix in the catalogue string itself, because TPS54335A and TPS54336A sit in one document and one distributor listing can point at the wrong row. The third is the reel size, since the same body ships on a large reel for volume and on a small reel for prototypes, and a line that runs out mid build finds out the hard way.
Our desk checks those three against the customer bill of materials before quoting, and when a lead time moves we show the alternative member of the family with the pin difference spelled out rather than a bare substitution. See component lead time solutions for how that comparison is presented.