SN65EPT22DGKR
Product Specifications
SN65EPT22DGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65EPT22DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65EPT22DGKR: a 3.3 V dual LVTTL to LVPECL buffer for clock trees
The SN65EPT22DGKR takes two LVTTL or LVCMOS inputs and drives two differential LVPECL outputs from a 3.3 V rail. It is the transmit side counterpart of the PECL to TTL translator: a CMOS clock or a logic signal goes in, and a differential pair comes out with the swing and the source impedance a PECL receiver expects. Clock frequencies up to 2.0 GHz are supported in the typical case, with 420 ps of typical propagation delay.
The supply window is 3.0 V to 3.6 V with ground as the reference, and the outputs expect a load returned to VCC minus 2 V, which is the standard PECL termination. Two channels in an 8 pin body make the part useful as a fanout buffer for a clock that has to reach two receivers, or as a differential driver for a single ended oscillator that has to travel to a backplane.
Key data for the SN65EPT22DGKR
| Channels | Two LVTTL or LVCMOS inputs, two differential LVPECL output pairs |
| Frequency | Clock frequencies to 2.0 GHz typical, measured at a 300 mV peak to peak output amplitude |
| Delay | 420 ps typical propagation delay from input to differential output |
| Levels | Output high 2155 mV to 2405 mV, output low 1355 mV to 1605 mV, the standard LVPECL window at 3.3 V |
| Supply | 3.0 V to 3.6 V, supply current 39 mA to 50 mA depending on the row and the temperature |
| Fail state | Deterministic high output when an input is left open, plus built in temperature compensation on the input stage |
Body, marking and reel data
| Body | DGK, VSSOP 8 at 3.00 mm by 3.00 mm, with a D SOIC 8 option at 4.90 mm by 3.91 mm |
| Reel | 2500 pieces on a large reel for the plain and G4 rows, carrier tape 12.4 mm |
| Marking | SIQI on the G4 row of the same body, so the finish and the code move together |
| Handling | Moisture level 1, 260 C peak, unlimited floor life, nickel palladium gold finish |
| Compatibility | Published as a drop in part for the MC100ELT23, which is the code a lot of older clock cards still print |
Where the dual buffer fits in a clock path
A single ended CMOS clock that has to cross a connector benefits from being converted to a differential pair before it leaves the board. The pair carries the same information with twice the noise margin, and a receiver at the far end can recover it after a loss that would have destroyed a single ended swing. Two channels in one body let one oscillator feed two destinations without a second package, which matters on a card where the clock tree has to stay star shaped.
Termination is the part that catches people out. The LVPECL output expects the load to be returned to VCC minus 2 V, so a 3.3 V rail means a 1.3 V termination rail, or the Thevenin equivalent of two resistors. Boards that terminate to ground will pull the output stage outside its intended operating point and the swing will collapse before the frequency limit is reached. Where a board has to terminate to ground, an emitter follower pair or an ac coupled network is needed and the buffer itself stays the same. The two channels share a supply pin, so a decoupling capacitor per output pair is the practical rule.
Questions we get when this code is on a BOM
The most common question is whether this part can drive a 100 ohm differential pair directly. It can, provided the pair is terminated at the far end into the correct rail, and provided the driver sees the parallel combination of the two 50 ohm legs. What the part does not include is an internal termination, so the four resistors that set the PECL levels are part of the board and part of the BOM we quote alongside the buffer.
The second question is about the difference between this part and the EPT21 or EPT22 family members with different channel counts. The suffix matters: the same 8 pin body is published with one and with two channels, and a substitution that ignores the suffix will leave half the clock tree undriven. We name the channel count on the offer and ask the buyer to confirm it against the board net list before the order is released.
How SUPERB supports this line item
We supply the SN65EPT22DGKR with the channel count, the body and the termination note stated on the offer. Customers who are moving a clock card from an older ECL buffer can send the original code to our obsolete part cross reference hub and receive a comparison against the EPT22 pinout and levels.
For production builds, the kitting service lets the clock section arrive as one kit: buffer, termination resistors and coupling capacitors counted per board, so the line does not stop because one 0402 value was missed in the pick list.