Contact Us

VBGQA1606

Brand: VBsemi
VBsemi VBGQA1606 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQA1606 — Discrete & Power Semiconductors | Superb Automation

VBGQA1606

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQA1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQA1606: 60 V and 60 A with a logic level gate

The VBGQA1606 is a single N channel MOSFET in a DFN8 body of 5 mm by 6 mm, rated at 60 V drain to source, plus or minus 20 V on the gate, a 2.5 V threshold, 60 A of drain current, 6.5 milliohm at a 4.5 V gate and 5.3 milliohm at 10 V. It is the 60 V member of the same 5 by 6 family as the 40 V and 80 V parts.

60 V is the class between a 48 V rail and an 80 V part. It covers a 48 V PoE feed with a modest margin, a 36 V battery, a 42 V automotive auxiliary rail and a 48 V telecom rail without load dump. The 2.5 V threshold makes it a logic level part, which is what a 5 V rail or a 3.3 V gate driver can drive directly in a small product.

60 A in a 5 by 6 body is a moderate die for the package, which is why the thermal path is workable at 5 W without a large copper area. The part sits in the middle of the family: more current than the small 3 by 3 parts and far less voltage stress than the 150 V member.

Key data for the VBGQA1606

ConfigurationSingle N channel
PackageDFN8, 5 mm by 6 mm, exposed pad
VDS60 V
VGSPlus or minus 20 V
Vth2.5 V typical
ID60 A, a die figure at a 25 C case
RDS(on) at 4.5 V6.5 milliohm
RDS(on) at 10 V5.3 milliohm
TechnologyShielded gate trench
Loss at 10 A0.65 W at a 4.5 V gate
Body diodeIntrinsic, cathode at the drain
Thermal pathPad and vias into the copper

Why a 60 V part exists between 48 V and 80 V

A 48 V rail with an 80 V part leaves 32 V of margin and a die that is larger than the job needs. A 60 V part leaves 12 V, which is enough for a clamped rail and not enough for a load dump. The reason the class is popular is cost and size: a 60 V die reaches 5.3 milliohm in a smaller area than an 80 V die of the same resistance, so the part is cheaper and the board is smaller.

The decision comes down to what the rail does when a load is removed. A 48 V PoE port with a hot unplug can ring 20 V above the rail for a microsecond, and a 60 V part is inside its ceiling with the clamp doing its job. A 48 V automotive rail with load dump is not, and there the 80 V or 100 V class is the only honest answer.

The threshold is also part of the choice. A 2.5 V threshold is right for a 5 V gate and wrong for a rail where the gate node can be pulled by a fast drain edge, since a low threshold makes the part easier to turn back on through the Miller capacitance. At 60 V the dv/dt is usually modest, so the trade is acceptable.

Thermal behaviour at 5 W in a 5 by 6 body

At 10 A and 6.5 milliohm the loss is 0.65 W, which needs almost no copper. At 25 A it is 4 W, and the pad plus a dozen vias plus a square inch of copper on each layer is what keeps the junction under 100 C in still air. At 40 A the loss is 10 W and the same body needs forced air or a much larger copper area.

The thermal resistance of the package is only one term. The solder joint under the pad, the voiding in it and the copper spreading all sit in series, and the datasheet figure assumes a good joint on a defined board. A pad with 20 per cent voiding behaves like a part with a much worse thermal resistance, which is why a large exposed pad is worth an X ray on the first build.

The vias carry the heat as well as the current. A via with a 0.3 mm drill and a thin plating is a poor thermal conductor, so a dozen vias in the pad is not the same as a copper filled area. Where the loss is above a few watts, the vias should be plated through and, where the process allows, filled.

Where the part fits and where it does not

It fits a 48 V PoE port switch, a 36 V battery disconnect, a 42 V auxiliary load switch, a synchronous rectifier on a 24 V output, and a 48 V fan or pump driver at moderate current. It does not fit an automotive 48 V rail with load dump, a 60 V bus at full derating, or a continuous current above 25 A without a thermal path that most small boards do not have.

For a 60 V switch on a 48 V rail, the deciding parameters are the threshold, the resistance at the gate voltage available and the transient the rail can produce. Our BOM shortage recovery page covers how a shortage is closed on a line without changing the switching behaviour of the board.

The sourcing side of this part is covered on the one stop BOM sourcing. For a 60 V switch with several small parts around it, that page covers how the group is bought on one order.

Questions we get on this code

Is 60 V enough for a 48 V rail? For a clamped telecom or PoE rail, yes. For an automotive rail with load dump, no, use an 80 V or 100 V part.

Can a 3.3 V gate drive it? At 3.3 V the die is above its 2.5 V threshold but not fully enhanced, and the 6.5 milliohm column is a 4.5 V figure. Use 4.5 V or more where the loss matters.

How much copper for 20 A? About 2.6 W of loss. A pad with vias into a plane and a square inch of copper per layer is the usual minimum in still air.

What should a purchase order carry? Part number, DFN8 5 by 6, and the reel quantity. We confirm the packing on the offer.