VBFB1806
Product Specifications
VBFB1806
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBFB1806 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBFB1806: an 80 V, 75 A N channel in TO251
The VBFB1806 is a single N channel MOSFET in TO251 rated at 80 V, plus or minus 20 V on the gate, 75 A of drain current, with a threshold of 3 V. The catalogue gives 9 milliohm at 4.5 V and 6 milliohm at 10 V, on trench silicon.
Eighty volts is the class for a 48 V system with margin, for a 60 V battery under charge, and for the primary side of a telecom converter. Six milliohm at 80 V is a large die, and a large die in a standing package is a thermal compromise.
The threshold of 3 V means the part is a 10 V drive device. At 4.5 V it conducts, at 3.3 V it barely does, and a logic pin is not the right driver.
Key data for the VBFB1806
| Configuration | Single N channel |
| Package | TO251, IPAK, upright with exposed tab |
| VDS | 80 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V |
| ID | 75 A |
| RDS(on) at 4.5 V | 9 milliohm |
| RDS(on) at 10 V | 6 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, recovery matters in a bridge |
| Thermal path | Tab in free air plus the leads |
| Gate charge | Not published, large die means a real driver is needed |
| Typical use | 48 V load switch, telecom input, motor drive |
Six milliohms at 80 V and what it costs
An 80 V die with 6 milliohm is roughly four times the area of a 100 V die at 30 milliohm, and the gate charge scales with area. Driving it at 100 kHz takes a gate driver with an amp of peak current, not a microcontroller pin through a resistor.
The reward is conduction loss. At 20 A the loss is 2.4 W, which in a TO252 with a pad would be an 80 C rise and in a standing TO251 nearer 140 C. So the package, not the die, sets the working current.
At 10 A the loss is 0.6 W and the standing body is fine. That is the honest continuous current for this part in free air, and it is a quarter of the rating on the page.
Eighty volts on a 48 V rail
A 48 V lead acid string floats at 54 V and equalises at 58 V, and a 48 V lithium pack charges to 54.6 V. Eighty volts leaves 20 V or more of margin, which covers the turn off spike of a modest load and the surge of a hot plug event.
It does not cover a telecom 60 V bus with a lightning surge, where the transient can reach 100 V or more. In that application a 100 V or 150 V part is used and the extra resistance is accepted.
For a 48 V hot swap, the safe operating area matters more than the resistance, because the part has to survive the inrush while the load capacitors charge. The catalogue page gives no safe operating area curve, so the data sheet has to be checked before the part is used as a hot swap switch.
The 48 V hot plug case is worth spelling out because it is where this part is most often misapplied. When a board is inserted into a live 48 V backplane, the load capacitors draw a current limited by the connector resistance and the capacitor ESR, and the switch has to survive that current at the full bus voltage for the time the capacitors take to charge. That is a safe operating area event, not a conduction event. Without a curve on the catalogue page, the only safe way to use the part is with a hot swap controller that ramps the gate, which keeps the die inside its area by trading voltage for current during the ramp.
Where the part is used as a plain load switch that closes once into a precharged load, the same event does not occur and the 48 V rating is comfortable. The distinction between those two uses is usually lost in a BOM review, and it is the first question worth asking when a 48 V line is quoted.
Telecom equipment is tested to surge standards that put hundreds of volts on a 48 V input for microseconds, and a 80 V part cannot hold that off. The usual arrangement is a transient suppressor across the input that clamps below 80 V, followed by the switch. The suppressor has to be chosen with the switch's leakage and the fuse's let through energy in mind, because a suppressor that clamps too late protects nothing and one that clamps too low conducts in normal operation.
Where the part fits and where it does not
It fits a 48 V load switch up to about 10 A, a 36 V or 48 V motor drive, the low side of a 48 V to 12 V buck, and a battery disconnect on a 48 V pack. It does not fit a 60 V telecom bus with surge, and it does not fit a hot swap position without a safe operating area check.
Our material requirements planning page covers how a part used on several boards is planned across a build, which is where a 48 V switch tends to sit.
The sourcing side of this part is covered on the safety stock planning. For a 48 V switch used across several products, that page covers how a buffer is sized against the build plan.
Questions we get on this code
Can it be driven at 4.5 V? Yes, with 9 milliohm instead of 6. The threshold of 3 V leaves 1.5 V of overdrive at the top of the window, which is enough to conduct but not to reach the best resistance.
Is a heatsink needed? Above about 1 W, yes. The tab is exposed and can take a clip, and that is the practical way to raise the standing package above 10 A.
Is the body diode a problem in a motor drive? It carries the freewheel current and its drop is about 0.8 V, so at 10 A it dissipates 8 W during the freewheel interval. That is a real number to put in the thermal budget.
What should a purchase order carry? Part number, TO251 body, packing and date code. We confirm availability on the quotation.