VBGL1252N
Product Specifications
VBGL1252N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGL1252N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGL1252N: 250 V and 80 A in a TO263 body
The VBGL1252N is a single N channel MOSFET in a TO263 body, the part most catalogues list as D2PAK. Drain to source is 250 V, the gate window is plus or minus 20 V, the threshold is 3.5 V typical, drain current is 80 A and on resistance is 16 milliohm at a 10 V gate. The silicon is a shielded gate trench, which is how a 250 V die reaches 16 milliohm without a superjunction process.
250 V is the rating that sits between the 150 V class used on 96 V and 110 V battery systems and the 600 V class used across a rectified 220 V main. It covers a rectified 110 V or 120 V AC rail at 170 V with about 45 per cent headroom, a 48 V system with a large margin for load dump and ringing, and the primary switch of a forward converter fed from a 150 V DC bus. It does not cover a 220 V main that has been rectified and smoothed, because 310 V is already above the ceiling before any spike is added.
The 80 A column has to be read against the body. A TO263 is a surface mount part and its whole thermal path is the tab soldered to copper, and that tab is about 10 mm by 9 mm. The die inside can pass 80 A at a 25 C case, but the solder joint and the copper under it usually cannot hold that without a generous area and a heavy copper layer. On most boards the usable continuous current is a good deal lower, and the honest figure comes from the copper, the layer count and the airflow rather than from the catalogue line.
Key data for the VBGL1252N
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 250 V |
| VGS | Plus or minus 20 V |
| Vth | 3.5 V typical |
| ID | 80 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 16 milliohm |
| Technology | Shielded gate trench |
| Body diode | Intrinsic, cathode at the drain |
| Thermal path | Tab to copper, no isolated substrate |
| Gate charge | Not on the catalogue page, ask for the curve before fixing a frequency |
| Creepage on the tab | 250 V on a 10 mm tab needs a slot or a coated surface at pollution degree 2 |
What a shielded gate trench gives at this voltage
A field plate inside the trench shields the gate from the drain. That drops the gate to drain charge and lets the epitaxial layer be thinner for the same breakdown voltage, which is why this die reaches 16 milliohm at 250 V while a plain trench part of the same area would sit nearer 25 to 30 milliohm. The visible side effects are a somewhat higher output capacitance near zero drain voltage and a body diode whose reverse recovery is not the fastest in the catalogue.
The 3.5 V threshold is a compromise rather than a logic level. It is high enough that a floating gate does not open the channel on leakage, and low enough that a 10 V driver turns the die fully on with a short rise time. Driving it from a 5 V rail is possible but the resistance column in the catalogue is quoted at 10 V, so a 5 V gate leaves the die less than fully enhanced and the loss rises by a factor the page does not state. Treat this as a 10 to 12 V gate part and set the driver rail accordingly.
Where the shielded gate helps most is a hard switched converter running above 100 kHz. The charge that has to be pushed in and pulled out of the gate is the dominant loss at light load, and a 16 milliohm die with a flat charge curve keeps that loss low. Where it helps least is a linear or a soft start application, since the die is chosen for resistance and not for safe operating area.
Margin, avalanche and the 250 V ceiling
A 250 V part on a 170 V rail leaves 80 V of room, which sounds comfortable until the drain node rings. A fast turn off into an inductive load puts the leakage inductance and the output capacitance into a resonant peak that can double the bus voltage for a few tens of nanoseconds, and the peak arrives at the drain while the channel is already closed. Snubbing and a short, tight loop deal with most of it, and a transient voltage suppressor at the bus deals with the rest.
If the circuit has to absorb energy that the clamp cannot take, the question becomes what the die does in avalanche. The catalogue page for this part does not print an avalanche energy rating, so a circuit that relies on it is relying on an unstated figure. Where the energy is real, either add a clamp sized for the current or ask for the avalanche curve before the board is committed.
The 250 V ceiling also sets the maximum working voltage once a derating rule is applied. At the common 80 per cent rule the part works to 200 V continuously, which covers a 170 V rectified rail, a 150 V DC bus and a 96 V battery pack with the top of charge included. It does not cover a 200 V DC bus, which needs the 300 V or 400 V class, and it does not cover a 220 V AC input.
Where the part fits and where it does not
It fits the primary switch of a single ended forward converter on a 150 V bus, the high side and low side of an H bridge on a 110 V DC bus, a battery disconnect on a 96 V pack, and the pass element of a linear pre regulator that drops from 170 V to 48 V at modest current. It does not fit a flyback on a rectified 220 V main, a PFC stage, or any place where the drain has to hold more than 200 V in normal operation.
For a primary switch on a bus that is already at 150 V, the pair of decisions that matter are the resistance at the gate voltage actually available and the thermal path under the tab. Our power management cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour rather than on the headline current.
The sourcing side of this part is covered on the component lead time solutions. For a 250 V switch that has to be bought ahead of a build, that page covers how the lead time is planned rather than discovered.
Questions we get on this code
How much current can it really carry on a four layer board? At 16 milliohm and 20 A the conduction loss is 6.4 W, which a 10 mm by 9 mm tab on two ounce copper with vias into an inner plane will pass. At 40 A it is 25.6 W and the joint becomes the limit. Work back from the loss the board can remove, not from the 80 A column.
Does it need a gate resistor? Yes, unless the driver is weak. A 2 to 10 ohm resistor in the gate sets the turn on slope and keeps the drain ringing inside the 250 V window. The turn off path can use a separate diode if the loss matters.
Can two of them be put in parallel? They can, and the two positive temperature coefficient of resistance helps sharing, but a parallel pair needs its own gate resistors and matched source paths. At 16 milliohm the resistance of the copper between the two sources is a real fraction of the total and it decides how the current splits.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel or tube quantity on the offer instead of assuming it.