Contact Us

VBGQF1208N

Brand: VBsemi
VBsemi VBGQF1208N is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQF1208N — Discrete & Power Semiconductors | Superb Automation

VBGQF1208N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQF1208N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQF1208N: 200 V in a 3 by 3 DFN

The VBGQF1208N is a single N channel MOSFET in a DFN8 body of 3 mm by 3 mm, rated at 200 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 18 A of drain current and 66 milliohm at a 10 V gate. It is a small part with a high voltage rating, which is a combination worth understanding before it is used.

200 V in a 3 by 3 body is close to the limit of what a moulded surface mount package can insulate. The exposed pad is the drain and it is about 2.4 mm by 1.7 mm, and the gap from the pad to the source and gate pins is a fraction of a millimetre. At 200 V that gap is the constraint, not the die, and the assembly has to be clean and, in a damp environment, coated.

The part suits an auxiliary supply, a startup circuit, a small flyback on a 110 V rail, a piezo or actuator driver at high voltage and low current, and any place where the board area is the problem and the current is a few amps. It does not suit a main power path.

Key data for the VBGQF1208N

ConfigurationSingle N channel
PackageDFN8, 3 mm by 3 mm, exposed pad
VDS200 V
VGSPlus or minus 20 V
Vth3 V typical
ID18 A, a die figure at a 25 C case
RDS(on) at 10 V66 milliohm
TechnologyShielded gate trench
Loss at 2 A0.26 W through the channel
Loss at 5 A1.65 W through the channel
Body diodeIntrinsic, cathode at the drain
Creepage200 V across a sub millimetre gap, coat the assembly where humidity is high

What a 3 by 3 pad can remove

An exposed pad of 2.4 mm by 1.7 mm is under 5 square millimetres. At 0.26 W the part is comfortable with no special copper. At 1.65 W it needs a plane underneath and a set of vias. At 5 W the junction will be near its limit in still air even with good copper, and the small body has little thermal mass to ride out a surge.

The thermal resistance of a 3 by 3 body is higher than a 5 by 6, and the datasheet figure is measured on a board with more copper than most products have. For a part used at a watt or two that does not matter, and for a part used at five watts it is the whole question.

The current enters the pad from one side, because the source and gate pins are on one edge and the drain is the pad. At 5 A the crowding is mild, and at 18 A the edge nearest the source is where the die runs hottest.

There is a third thermal consideration in a body this small: the gate and source pins sit on one edge and the die is close to them, so heat travels into the pins as well as into the pad. A part dissipating a watt raises the temperature of the solder at the pins by a few degrees, and a part dissipating three watts by a good deal more. On a board with a tight pitch that heat reaches the neighbouring components, and a temperature sensitive part placed next to it will drift. Keep the part away from a crystal, a reference or an analogue front end, and give the copper around it a path to the plane so the heat goes down instead of sideways.

200 V in a small body: the insulation question

The drain pad sits at the switching node, so it moves by 200 V every cycle. Next to it are the source and gate pins at a fraction of a millimetre. In dry air that gap holds. In a humid or contaminated assembly, a surface film can conduct and the leakage shows up as a slow drift rather than a failure.

The practical answer is a conformal coat, or a keep out on the copper around the pad so the voltage stands across moulding rather than across a board surface. A slot in the copper between the pad and the gate trace is cheap and effective.

The second insulation question is the gate loop. At 200 V and a fast edge, the gate sees a coupled charge through the Miller capacitance and a small part has a small gate charge, so the fraction is larger. A 10 kohm gate to source resistor plus a short gate return keeps the part off when the driver is not driving.

Where the part fits and where it does not

It fits a startup circuit on a 150 V bus, an auxiliary flyback at a few watts, a piezo driver, a high voltage level shifter, and a small relay or solenoid driver on a 110 V rail. It does not fit a main power path at 10 A, a 220 V rectified rail, or a board where the assembly cannot be coated and the environment is damp.

For a small body at high voltage, the two things that decide whether a substitute works are the pad geometry and the gate charge. Our how to verify a drop in replacement page sets out the checks made before a substitute is accepted in that position.

The sourcing side of this part is covered on the supplier onboarding checklist. For a small high voltage part, that page covers what a new source has to document before its first shipment.

Questions we get on this code

Is 200 V enough for a 110 V bus? Yes, with margin for a clamped transient. It is not enough for a rectified 220 V main.

Does it need a coating? On a damp or dirty assembly, yes. The pad to pin gap is the reason.

How much current in still air? About 2 to 3 A with a pad and a plane, based on a watt of loss. Above that the junction climbs quickly.

What should a purchase order carry? Part number, DFN8 3 by 3, and the reel quantity. We confirm the packing on the offer.