Contact Us

OPA694IDBVT

Brand: Texas Instruments
Texas Instruments OPA694IDBVT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA694IDBVT — Power Management & Signal Chain | Superb Automation

OPA694IDBVT

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA694IDBVT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA694IDBVT: 1700 volts per microsecond current-feedback operational amplifier in a 5-pin SOT-23

OPA694IDBVT is a current-feedback operational amplifier in SOT-23-5 with more than 500 MHz of bandwidth, 1700 volts per microsecond and 5.8 milliamps of supply current in a SOT-23 body of 5 pins. The IDBVT suffix is the industrial grade in the 5-pin SOT-23 body supplied on a 250 piece tape. The part gives more than 500 MHz of bandwidth at a gain of plus 2 with 1700 volts per microsecond of slew, draws 5.8 milliamps typical and 6.2 milliamps maximum, and keeps the output within 1.5 V of each rail, which is what allows a wideband stage to run on a single 5 V supply in a footprint the size of a grain of rice.

Order code and package

Order codeOPA694IDBVT
Functioncurrent-feedback operational amplifier in a 5-pin package
PackageSOT-23, 5 pins, body code DBV, 250 piece tape
Supplysingle 5 V or plus or minus 5 V, with the output 1.5 V inside each rail
Supply current5.8 milliamps typical, 6.2 milliamps maximum
Bandwidthmore than 500 MHz
Slew rate1700 volts per microsecond, published as 1700 volts per millisecond in the features list
Gainspecified at a gain of plus 2, with the feedback resistor setting the compensation
Output headroomwithin 1.5 V of either rail
Inputcurrent-feedback, high impedance inverting node
DatasheetOPA694 current-feedback family document

Electrical parameters that decide the application

Supply range5 V single supply or plus or minus 5 V split, both specified
Maximum quiescent6.0 milliamps at a 5 V supply, 6.2 milliamps at plus or minus 5 V
Feedback networka fixed resistor value from the datasheet is required for stability
Output drivesufficient for a back terminated video line at 5 V
Turn on timeshort, so the part can be duty cycled in a portable product
ThermalSOT-23 body, with the ground and supply pins as the heat path
Operating rangeindustrial

Points to check before this part goes on a BOM

The features list prints the slew rate as 1700 volts per millisecond, which is a typographical error for 1700 volts per microsecond. The number has to be read against the bandwidth: 1700 volts per microsecond at a 2 V peak to peak signal gives 135 MHz of full power bandwidth, and the small signal bandwidth is above 500 MHz, so on a full 2 V signal the slew rate is the limit by a factor of four. A specification review that takes the printed unit at face value concludes the part is unusable.

The 1.5 V of output headroom is the specification that makes a single 5 V supply workable. On 5 V the output can reach 3.5 V, so a 2 V peak to peak signal centred at 2.5 V fits with no margin at the top and 1 V at the bottom. A video signal with a 1 V peak to peak range and a sync tip at 0.3 V therefore fits, while a 2 V peak to peak signal centred at 2.5 V does not, and the datasheet does not hide that.

Current-feedback amplifiers are specified at a particular gain because the feedback resistor sets the compensation. This part is specified at a gain of plus 2, so a circuit built at a gain of plus 1 or plus 10 needs the resistor value recalculated from the family curves. The bandwidth does not fall as fast as a voltage-feedback part's would, which is the advantage, but the stability still depends on the resistor rather than on the gain alone.

5.8 milliamps typical and 6.2 milliamps maximum on a 5 V supply is 29 to 31 milliwatts, and in a 5-pin SOT-23 with a thermal resistance near 250 degrees per watt that is about a 7 degree rise. That is comfortable, and it is why the part suits a handheld product where the amplifier sits within a millimetre of a plastic case. Driving a terminated cable adds tens of milliwatts, which is still inside the package's capability but no longer negligible.

A 5-pin SOT-23 has one pin fewer than the usual operational amplifier footprint, so the inverting node, the non-inverting node and the output are the only signal pins, with supply and ground on the remaining two. The feedback network therefore has to be short and the ground return has to be a real plane, because at 500 MHz the parasitic inductance of a via is a significant fraction of an ohm and the current-feedback loop is sensitive to it. A socket or a long trace turns this part into an oscillator.

The part appears in portable products because 500 MHz in a 5-pin package removes the need for a separate buffer, and because the current-feedback topology holds its bandwidth at a gain of plus 2 where a voltage-feedback part of the same quiescent current would be down to a few hundred megahertz. The trade is the fixed feedback resistor, the 1.5 V of headroom and the sensitivity of the inverting node to stray capacitance, all three of which are manageable on a four layer board and none of which are manageable on a breadboard.

Where this order code fits

Portable video drivers, camera front ends, high speed line drivers and any wideband stage that has to fit in a handheld product use this part. A SOT-23 body with 500 MHz is unusual and the 1.5 V of output headroom is what makes it work from 5 V single supply rails. Boards comparing it with a neighbouring part start from our How to Choose an RF Amplifier page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Is the printed slew rate of 1700 volts per millisecond correct? No. It is a typographical error for 1700 volts per microsecond, which is consistent with the published bandwidth and the output stage. The rest of the datasheet uses microsecond units.

Can this part run from a single 5 V supply? Yes, and that is one of the reasons it exists. The output stays 1.5 V inside each rail, so the usable swing on 5 V is about 3.5 V and a video signal with a sync tip near ground fits.

Does the gain of plus 2 mean it cannot be used at unity gain? It means the datasheet numbers belong to a gain of plus 2. At other gains the feedback resistor has to be recalculated from the family curves, and the bandwidth and stability follow that resistor.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the RF Component Sourcing page sets out the checks that keep a substitute from failing on the bench.