Contact Us

OPA350UA

Brand: Texas Instruments
Texas Instruments OPA350UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA350UA — Power Management & Signal Chain | Superb Automation

OPA350UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA350UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA350UA: 38 MHz rail-to-rail CMOS operational amplifier with 5.2 milliamps of supply current in an 8-pin SOIC

OPA350UA is a rail-to-rail CMOS operational amplifier with 38 MHz of gain bandwidth, 22 volts per microsecond of slew and picoamp input bias current in a SOIC body of 8 pins. The UA suffix is the 8-pin SOIC body. The amplifier is specified from 2.7 V to 5.5 V, reaches 38 MHz at unity gain with 22 volts per microsecond, draws 5.2 milliamps typical and 7.5 milliamps maximum, and holds input bias current to 10 picoamps maximum, which is what makes a 38 MHz part usable as a transimpedance stage.

Order code and package

Order codeOPA350UA
Functionrail-to-rail output CMOS operational amplifier, unity gain stable
PackageSOIC, 8 pins, body code D
Supply range2.7 V to 5.5 V
Supply current5.2 milliamps typical, 7.5 milliamps maximum
Gain bandwidth38 MHz at unity gain
Slew rate22 volts per microsecond
Offset150 microvolts typical, 500 microvolts maximum at 5 V, 1 millivolt over temperature
Offset drift4 microvolts per degree
Input bias current0.5 picoamps typical, 10 picoamps maximum
Input common mode100 millivolts beyond either rail
DatasheetOPAx350, OPA2350, OPA4350 family document

Electrical parameters that decide the application

Voltage noise7 nanovolts per root hertz at 10 kHz, 4 microvolts RMS from 100 Hz to 400 kHz
Power-supply rejection40 microvolts per volt typical, 150 microvolts per volt maximum
Common-mode rejectionrail-to-rail input stage with the crossover inside the specified window
Channel separation0.15 microvolts per volt at DC on the dual and quad
Outputrail-to-rail, capable of driving a converter's sampling capacitor
Test conditionspecified into 1 kilohm connected to mid-supply
ThermalSOIC body, junction range minus 40 to plus 85 C for the specification

Points to check before this part goes on a BOM

38 MHz and 22 volts per microsecond are a matched pair: at a 2 V peak to peak signal the slew limit is 1.75 MHz and the gain limit at unity is 38 MHz, so the part is usable as a wideband buffer and as a gain stage up to about a megahertz at a gain of 20. Above that the slew rate, not the gain, sets the maximum amplitude, and a 4 V peak to peak signal at 1 MHz already needs 12.6 volts per microsecond of the 22 available.

10 picoamps of maximum bias current through a 1 megohm feedback resistor is 10 microvolts, and through 10 megohms it is 100 microvolts. A photodiode preamplifier with a 1 megohm transimpedance therefore carries an offset of 10 microvolts from bias current alone, well under the 500 microvolt offset, and the noise from the resistor dominates from a few kilohertz upward. This is the specification that separates the part from a bipolar amplifier of the same bandwidth.

5.2 milliamps typical and 7.5 milliamps maximum at 5 V is 26 to 37 milliwatts, which is the price of 38 MHz in a CMOS process. A quad in the same family draws 30 milliamps typical, so a four channel photodiode board needs a thermal plan as well as a current budget. The maximum figure is what a production budget should use, because the typical is a 25 C number.

The offset of 500 microvolts maximum and 1 millivolt over temperature is the weak point of a high speed CMOS amplifier. On a 12 bit converter at 5 V that is 0.4 to 0.8 of a bit, so it is acceptable; on a 16 bit converter the same window is 6.6 to 13 bits, and the channel needs either a calibration or a chopper. The 4 microvolts per degree drift is what turns the 500 microvolts into 1 millivolt over the industrial range.

4 microvolts RMS over a 400 kHz band is 0.34 of a bit on a 12 bit converter at 5 V, which is consistent with a 12 bit application. For a 16 bit converter the same noise is 5.5 bits, and narrowing the band to 10 kHz brings it to about 0.6 microvolts RMS, which would be 0.8 of a bit at 16 bits. The lesson is that the converter resolution and the amplifier bandwidth have to be chosen together, and a 38 MHz part is wasted behind a 10 kHz filter unless the bias current is the reason for choosing it.

The input works 100 millivolts beyond either rail and the output is rail to rail, so the part can buffer a 0 to 5 V signal on a single 5 V supply without a negative rail. What it cannot do is accept a signal that swings 0.5 V past the rail without the input protection conducting, so a board that expects overshoot from a cable needs a series resistor, and the resistor adds its own noise and its own bias current error to a part whose bias current was chosen to be negligible.

Where this order code fits

Photodiode and photomultiplier front ends, CCD and CMOS sensor buffers, fast 12 bit converter drivers and video distribution use this part. The combination of picoamp bias, rail-to-rail output and 38 MHz is what a photodiode preamplifier needs when the feedback resistor is in the hundreds of kilohms. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.

Questions buyers ask

Is the OPA350 a good photodiode preamplifier? Yes, because the bias current is 10 picoamps maximum, so a 1 megohm feedback resistor sees 10 microvolts of offset from bias current against 500 microvolts of amplifier offset. The 38 MHz bandwidth also supports a high transimpedance without a second stage.

Why does the maximum supply current matter here? Because the typical 5.2 milliamps is a 25 C figure and the maximum is 7.5 milliamps. A four channel board draws 30 milliamps into a small package, so the budget and the thermal plan both have to use the maximum.

Can this part drive a 16 bit converter? Only with calibration. The 500 microvolt offset is 6.6 bits at 16 bits on a 5 V range, and the 4 microvolts per degree drift takes it to 1 millivolt over the industrial range.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Choose an RF Amplifier page sets out the checks that keep a substitute from failing on the bench.