Contact Us

OPA277P

Brand: Texas Instruments
Texas Instruments OPA277P is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA277P — Power Management & Signal Chain | Superb Automation

OPA277P

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA277P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA277P: high-precision operational amplifier with 10 microvolt offset in an 8-pin plastic DIP

OPA277P is a precision operational amplifier intended as a direct replacement for the OP-07, OP-77 and OP-177, with 10 microvolts of offset and 1 nanoamp of bias current in a PDIP body of 8 pins. The P suffix is the 8-pin plastic DIP, and the family is specified over the whole plus or minus 5 V to plus or minus 15 V range rather than at a single supply, which is unusual and useful. Offset is 10 microvolts typical with a 20 microvolt maximum at 25 C, drift is 0.1 microvolts per degree, bias current is 1 nanoamp maximum, and the gain bandwidth product is 1 MHz with 0.8 volts per microsecond of slew.

Order code and package

Order codeOPA277P
Functionprecision operational amplifier, unity gain stable
PackagePDIP, 8 pins, body code P
Supply rangeplus or minus 2 V to plus or minus 18 V
Quiescent current790 microamps typical, 825 microamps maximum, 900 microamps over temperature
Gain bandwidth1 MHz
Slew rate0.8 volts per microsecond
Settling14 microseconds to 0.1 percent, 16 microseconds to 0.01 percent on a 10 V step
Output swingwithin 0.5 V of the negative rail and 1.2 V of the positive rail into 10 kilohms
Offset trimpin 5, leave floating when unused
Junction rangeminus 40 to plus 85 C
DatasheetSBOS079C, revision of February 2023

Electrical parameters that decide the application

Offset at 25 C10 microvolts typical, 20 microvolts maximum
Offset drift0.1 microvolts per degree
Input bias current1 nanoamp maximum
Common-mode rejection140 dB
Open-loop gain134 dB into 2 kilohms, 140 dB into 10 kilohms
Power-supply rejection130 dB
Total harmonic distortion0.002 percent at 1 kHz and 3.5 volts RMS
Short-circuit current35 milliamps
Overload recovery3 microseconds with the input driven to the rail
Output impedance40 ohms at 1 MHz, open loop

Points to check before this part goes on a BOM

20 microvolts on a 10 V span is 2 parts per million, and a 16 bit converter on the same span has a bit of 152 microvolts, so the offset is an eighth of a bit and needs no trim. Drift is the term to check: 0.1 microvolts per degree over 100 degrees is 10 microvolts, half the initial offset, so a channel trimmed at 25 C stays inside a quarter of a 16 bit bit over the industrial range, which is why this amplifier is used without a trim network at all.

140 dB of common-mode rejection is the figure that carries a bridge. A 10 V common-mode shift on a bridge excited from the same supply produces 10 V divided by 10 to the seventh, which is 1 microvolt at the input. The same shift through a 100 dB amplifier would produce 100 microvolts, a hundred times the offset, so the rejection rather than the offset is what decides the usable bridge excitation on an unchopped amplifier.

1 nanoamp of bias current is the practical limit on source impedance. Through 100 kilohms it is 100 microvolts, which is 0.66 of a 16 bit bit at 10 V, and through 1 megohm it is 1 millivolt, which is seven bits. A precision amplifier with a nanoamp of bias wants a source below about 100 kilohms, and a photodiode or an electrometer head needs a different input stage entirely.

The supply range is plus or minus 2 V to plus or minus 18 V with the specification held across the whole span. At the bottom of that range the output swing of 0.5 V from the negative rail and 1.2 V from the positive rail leaves a 1.8 V window on a 4 V total supply, which is a genuine constraint rather than a footnote. Most boards run plus or minus 15 V, where the swing is plus or minus 13.8 V into 10 kilohms.

The amplifier is specified as a replacement for the OP-07, OP-77 and OP-177, and the numbers show why: the same pinout, 10 microvolts against tens of microvolts, 0.1 microvolts per degree against a wider drift, and twice the speed at half the quiescent current. In a socket where the OP-07 was trimmed with a potentiometer, the trim network should be removed or left floating rather than re-used, because the offset it was nulling is no longer there.

790 microamps per amplifier on plus or minus 15 V is 23.7 milliwatts, and the 900 microamp maximum over temperature is 27 milliwatts. A quad would be 108 milliwatts, which is a real load on a linear supply and enough to matter on a board that has been running the same sockets with OP-07s at similar current. The gain bandwidth of 1 MHz and the 0.8 volts per microsecond are the compromise that buys the rejection and the low drift.

Where this order code fits

Bridge and strain gauge front ends, precision current sources, thermocouple cold junction stages and any socket that currently holds an OP-07 or OP-177 use this part. The low bias current and 140 dB common-mode rejection are what make it a drop-in improvement in older instrumentation rather than a rework of the board. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can an OPA277P replace an OP-07 in the same socket? Yes. The pinout matches, the supply range covers plus or minus 15 V, and the offset trim pin is the same one. The trim potentiometer should be left out rather than re-used, since the initial offset it was correcting is now 20 microvolts.

Why is 1 nanoamp of bias current described as a limit? Because the error it creates grows with source resistance. One nanoamp through 100 kilohms is 100 microvolts, which is already most of a 16 bit bit on a 10 V range, and through a megohm it is a millivolt.

Is the amplifier specified at 5 V as well as at plus or minus 15 V? Yes. The family is specified across the plus or minus 5 V to plus or minus 15 V range with one limit set, and the minimum supply is plus or minus 2 V, where the output window narrows to about 1.8 V.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.