Contact Us

MSP430L092SPW

Brand: Texas Instruments
Texas Instruments MSP430L092SPW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MSP430L092SPW — Power Management & Signal Chain | Superb Automation

MSP430L092SPW

Texas Instruments — Power Management & Signal Chain

Product Overview

The MSP430L092SPW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MSP430L092SPW: 0.9 V ultra low voltage microcontroller with an analog pool in a 20-pin TSSOP

MSP430L092SPW is a 16 bit microcontroller that runs from a single 0.9 V cell and carries an analog pool of converter, comparator and reference blocks in a TSSOP body of 20 pins. The L092 is built for one job: running from a single cell that is nearly flat. The supply range is 0.9 V to 1.5 V at 1 MHz and 1.5 V to 1.65 V at 4 MHz, active current is 45 microamps per megahertz, standby is 6 microamps in low power mode 3 and off is 3 microamps. Inside the part is a 2 KB RAM array with 1792 bytes free plus two lockable blocks, a 2 KB loader ROM, two 16 bit timers and an analog pool that can be configured as an 8 bit converter, an 8 bit digital to analog converter, a comparator, a supply monitor and a temperature sensor.

Order code and package

Order codeMSP430L092SPW
Function16 bit ultra low voltage microcontroller with an analog pool
PackageTSSOP, 20 pins, body code PW
Supply range0.9 V to 1.5 V at 1 MHz, 1.5 V to 1.65 V at 4 MHz
RAM2 KB, 1792 bytes free plus 128 bytes and 96 bytes lockable
ROM2 KB loader ROM with service functions
Timerstwo 16 bit Timer_A blocks with three capture and compare registers each
Analog8 bit converter, 8 bit digital to analog converter, comparator, supply monitor, temperature sensor and reference
Clock1 MHz internal trimmable high frequency clock and a 20 kHz low frequency clock
I/Oup to 11 pins with ultra low voltage port logic
DatasheetSLAS673, September 2010

Electrical parameters that decide the application

Active current45 microamps per megahertz at 1.3 V
Standby current6 microamps in low power mode 3 with the watchdog running
Off current3 microamps in low power mode 4
Wake up timeunder 5 microseconds
Port output lowbetter than 0.15 V at 2.5 mA
Port output highbetter than VCC minus 0.15 V at 1 mA
Brownoutultra low voltage brownout circuit with RAM retention below the trip point
Watchdog32 bit watchdog timer
PWMTimer0 and Timer1 PWM available on all ports
Programmingfour wire JTAG, plus a bootstrap loader in the L092

Points to check before this part goes on a BOM

The supply range is split by clock, and the split is the whole supply constraint. A 0.9 V cell supports 1 MHz, and 4 MHz needs 1.5 V, so firmware that raises the clock when a conversion finishes has to check the rail first. Running 4 MHz from a 1.2 V cell is outside the specified condition even though the part may start.

Off mode at 3 microamps is not small enough for a product that sleeps for a year, so this part is used where the duty cycle keeps it in a shallow sleep rather than in a deep one. 6 microamps in low power mode 3 with a 1 percent duty cycle costs more than the measurement itself, and that arithmetic decides the battery size.

The analog pool is a set of blocks that are wired by register settings rather than a fixed converter. The same pins become an 8 bit converter, a comparator with a reference, a digital to analog output or a supply monitor, so a product can measure a sensor, compare it against a threshold and drive an output without an external analog part, at the cost of firmware that reconfigures the pool between uses.

The port logic is built for the low rail. Output low is better than 0.15 V at 2.5 mA and output high is within 0.15 V of the supply at 1 mA, which is what allows a light emitting diode or a small buzzer to be driven directly from a 1.2 V rail without a charge pump.

The 2 KB loader ROM is not user code space. It carries service functions used by the bootstrap loader, so the free memory is the 1792 bytes of RAM plus the lockable blocks, and a program larger than that has to be split across the lockable areas with an explicit copy step at start up.

There is no flash on this part, which is the reason it can run at 0.9 V at all. Program memory is RAM loaded at start up from an external source or from the loader, so a product that needs to retain firmware through a battery change has to provide non volatile storage outside the microcontroller.

Where this order code fits

Single cell battery products use this code: medical patches, disposable testers, energy harvesting nodes and any device whose end of life voltage is below the 1.8 V floor of a conventional microcontroller. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.

Questions buyers ask

Can this run from a single alkaline cell? Yes, at 1 MHz down to 0.9 V. A 4 MHz clock needs 1.5 V, so the clock has to follow the cell voltage as it discharges.

Does it have flash memory? No. The program lives in RAM with a 2 KB loader ROM for service functions, so retention across a power loss needs non volatile storage on the board.

What is the analog pool used for? It configures the same pins as an 8 bit converter, a comparator, a digital to analog output, a supply monitor or a temperature sensor, so a small product can do its whole measurement chain without external analog parts.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.