Contact Us

ST1S10PHR

Brand: ST
ST1S10PHR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine ST1S10PHR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

ST1S10PHR — Voltage Regulator by STMicroelectronics

The ST1S10PHR is an STMicroelectronics voltage regulator in SOIC-8_EP_150mil for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
ST1S10PHRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberST1S10PHR
PackageSOIC-8_EP_150mil
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The ST1S10PHR is an STMicroelectronics voltage regulator in SOIC-8_EP_150mil package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the ST1S10PHR?

Check the specific variant. The ST1S10PHR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics ST1S10PHR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

ST1S10PHR: 3 A at 900 kHz, synchronous, in PowerSO-8

ST1S10PHR is a monolithic synchronous step down regulator from STMicroelectronics in the PowerSO-8 body, tape and reel. It delivers up to 3 A, takes an input from 2.5 V to 18 V, sets the output from 0.8 V up to 0.85 times the input with two resistors, and switches at a fixed 900 kHz. The synchronous rectifier is inside the part, which is the reason there is no Schottky diode in the bill and no diode loss in the thermal sum.

The 900 kHz figure is what allows small external parts. At that frequency the inductor is a couple of microhenries and the output capacitor is a ceramic of a few tens of microfarads, so the whole regulator fits in a corner of a dense board. The part can also be synchronised to an external clock between 400 kHz and 1.2 MHz, which is how a system avoids putting two switching tones in the same band.

Vendor figures for this code

FunctionSynchronous step down PWM regulator, current mode
Output current3 A
Input voltage2.5 V to 18 V
Output voltageAdjustable from 0.8 V to 0.85 times the input
Output tolerance2 percent DC
Switching frequency900 kHz fixed, or synchronised from 400 kHz to 1.2 MHz
Efficiency90 percent typical
Standby current6 microamps maximum over temperature
Junction rangeminus 40 to plus 125 degrees
ProtectionsThermal, switching overcurrent, dynamic short circuit
Other functionsInternal soft start, inhibit
PackagePowerSO-8, also DFN8 4 by 4 mm in the family

Synchronous means the loss moves, it does not disappear

Replacing the diode with a second switch removes the forward drop but adds a switching loss and a body diode conduction interval at every cycle. At 900 kHz that interval is a small fraction of the period and the net gain is real, which is where the 90 percent typical efficiency comes from. At a lower frequency the diode loss would dominate and a synchronous part would gain less, so the frequency and the rectifier choice belong to the same decision.

The 6 microamps of standby current is the figure that matters on a product with a sleep mode. A regulator that draws a milliamp in standby will flatten a battery in weeks, and one that draws microamps will not. That is why this family is named for point of load regulators and for pre-regulation ahead of a linear stage, both cases where the rail stays alive while the load sleeps.

Where it is used, and what follows on

Typical uses are point of load rails in set top boxes, optical storage, printers and network equipment, and the pre-regulator in front of a low dropout stage. Related pages are power management cross reference, pin to pin cross reference, and component lead time solutions.

Questions buyers ask on this code

The first is the difference between the PHR and the PUR suffix, which is the package rather than the silicon, PowerSO-8 against DFN8, and the two need different pad geometry. The second is whether 3 A can be drawn continuously, and the answer depends on the copper under the exposed pad, the ambient and the input voltage, because the losses rise with the input to output ratio. The third is the switching frequency, which is fixed at 900 kHz unless an external clock is provided, and an external clock outside the 400 kHz to 1.2 MHz window is not accepted by the part.