Contact Us

MSP430G2553IPW20

Brand: Texas Instruments
Texas Instruments MSP430G2553IPW20 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MSP430G2553IPW20 — Power Management & Signal Chain | Superb Automation

MSP430G2553IPW20

Texas Instruments — Power Management & Signal Chain

Product Overview

The MSP430G2553IPW20 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MSP430G2553IPW20: 16 bit value line microcontroller with 16 KB flash and a 10 bit ADC in a 20-pin TSSOP

MSP430G2553IPW20 is a 16 bit microcontroller with 16 KB of flash, 512 bytes of RAM, a 10 bit converter and two serial interfaces in a 20-pin body in a TSSOP body of 20 pins. The G2553 is the largest member of the value line family and this PW20 code is the 20-pin TSSOP with 16 I/O pins. It carries 16 KB of flash, 512 bytes of RAM, a 10 bit successive approximation converter with eight channels, two Timer_A blocks with three capture and compare registers each, one USCI block that can be a UART, SPI or I2C port, a comparator and a four frequency calibrated oscillator that reaches 16 MHz.

Order code and package

Order codeMSP430G2553IPW20
Function16 bit RISC microcontroller, value line
PackageTSSOP, 20 pins, body code PW
Flash16 KB plus four information segments of 64 bytes
RAM512 bytes
Supply range1.8 V to 3.6 V
ADC10 bit successive approximation, eight channels
Timerstwo Timer_A blocks, three capture and compare registers each
Serialone USCI block, UART, SPI or I2C
I/O16 pins
DatasheetSLAS735 revision J, covering the G2x53 and G2x13 devices

Electrical parameters that decide the application

Clockup to 16 MHz from the calibrated DCO, four calibrated frequencies
ADC resolution10 bit, 8 channels, with an internal reference option
ComparatorCOMP_A+ with a reference ladder
Flash segments512 byte main segments, four 64 byte information segments
Information segment Aholds factory calibration data and is protected after reset
ProgrammingSpy-Bi-Wire two wire interface on the test pins
Low power modesfive, with the standard MSP430 wake behaviour
WatchdogWDT+ with a clock independent mode
Brownouton chip brownout reset
Pin count trade20 pins with 16 I/O against 28 pins with 24 I/O in the larger body

Points to check before this part goes on a BOM

The 10 bit converter on this part is a successive approximation block with eight channels, not the sigma delta converter of the metering family. One bit at 10 bits on a 3.3 V reference is 3.2 mV, so a signal of a few millivolts needs the internal gain stage or an external amplifier and the 16 bit word of the core does not recover resolution the converter never produced.

Two Timer_A blocks with three capture and compare registers each give six compare channels, which covers a three phase PWM plus two capture inputs, or a single phase PWM with dead time on separate outputs. The 16 bit core at 16 MHz has one instruction cycle per clock, so a 20 kHz control loop has about 800 instructions per period to work with.

The USCI block does UART, SPI and I2C on the same pins with the mode selected in software, which is how a 20-pin part drives a display over I2C and a host over UART without extra pins. Only one mode is active at a time, so a product that needs two simultaneous serial ports has to move to a part with two USCI blocks.

Information segment A carries factory calibration for the DCO and the temperature sensor and is write protected after reset. Erasing it loses the calibrated frequencies, and code that unlocks the segment to use the space as general memory pays for it with an uncalibrated clock on that unit.

The 20-pin body carries 16 I/O, and the analog inputs share pins with port 1. A board using all eight converter channels leaves eight digital pins, so the pin budget is the deciding factor between this code and the 28-pin body with 24 I/O.

Spy-Bi-Wire uses two pins for programming and debugging, which keeps a production header small. The same pins are usable as port pins in the application, so a board that needs the last two pins loses the ability to reprogram the part after assembly without a fixture that can drive those nodes.

Where this order code fits

Small instrument front panels, sensor nodes, teaching boards and low cost controllers that need a 16 bit core and a converter in a package small enough for a 20 mm wide board use this code, and the I2C capable serial block covers an external display or a memory device without a second part. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.

Questions buyers ask

Is the 10 bit converter enough for a load cell? For a coarse reading, yes, but a 1 mV per volt sensitivity bridge gives a few millivolts at full scale, which is only a handful of counts at 10 bits. A load cell usually needs an external amplifier or a part with a sigma delta converter.

Can this code do I2C and UART at the same time? No. The single USCI block is one port at a time, selected in software. Two simultaneous serial ports need a part with two USCI blocks.

What is the largest body in this family? The 28-pin TSSOP with 24 I/O. This code is the 20-pin version with 16 I/O, and both carry the same 16 KB of flash and 512 bytes of RAM.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.