MSP430F135IPM
Product Specifications
MSP430F135IPM
Texas Instruments — Power Management & Signal Chain
Product Overview
The MSP430F135IPM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
MSP430F135IPM: 16 bit microcontroller with 16 KB flash, a 12 bit ADC and 512 bytes of RAM in a 64-pin LQFP
MSP430F135IPM is the largest flash member of the F13x family, with a 12 bit converter and twice the RAM of the code below it in a LQFP body of 64 pins. This code takes the F133 and doubles both memories: 16 KB of main flash plus 256 bytes of information memory, and 512 bytes of RAM in place of 256. The converter, the two 16 bit timers, the USART, the hardware multiplier and the 48 I/O pins are unchanged, and the same 64-pin PM body carries all of it at 280 microamps per megahertz in active mode.
Order code and package
| Order code | MSP430F135IPM |
| Function | 16 bit RISC microcontroller with a 12 bit ADC |
| Package | LQFP, 64 pins, body code PM |
| Flash | 16 KB plus 256 bytes of information memory |
| RAM | 512 bytes |
| Supply range | 1.8 V to 3.6 V |
| ADC | 12 bit with internal reference, sample and hold, autoscan |
| Timers | Timer_A3 and Timer_B7 with shadow registers |
| Serial | one USART, UART or SPI |
| I/O | 48 pins |
| Datasheet | SLAS272, F13x and F14x family document |
Electrical parameters that decide the application
| Active current | 280 microamps at 1 MHz from 2.2 V |
| Standby current | 1.6 microamps |
| Off current | 0.1 microamps with RAM retained |
| Instruction cycle | 125 nanoseconds at 8 MHz |
| Wake up time | under 6 microseconds |
| RAM advantage over F133 | 512 bytes against 256, which is 64 converted samples at 12 bits |
| Flash advantage | 16 KB against 8 KB, doubled |
| Multiplier | 16 by 16 hardware multiplier |
| Low power modes | five |
| Supply supervision | power on reset, brownout and watchdog |
Points to check before this part goes on a BOM
The 512 bytes of RAM is the reason to pay for this code. A 12 bit sequence of 128 samples needs 256 bytes already, so a moving average over 128 points plus a protocol buffer fits here and does not fit in the 8 KB member, and the difference between the two parts is a firmware architecture rather than a specification line.
16 KB of flash is enough for a display driver, a metering algorithm and a field protocol with room for a boot loader in the top segments. The information segments stay separate, so calibration constants survive a code update, which is the arrangement a product shipped into a calibration-critical market needs.
Current consumption does not grow with the memory, so this code runs at the same 280 microamps per megahertz as the 8 KB part. The power budget is set by the duty cycle and the clock, and the extra memory only changes the static leakage of the larger array by a small amount that is inside the specification spread.
The 64-pin body gives 48 I/O, but the analog channels sit on port 6 and are shared with digital functions. A board that scans eight external channels and also needs a parallel display loses part of the digital count, so the pin budget has to be drawn with the channel assignment in view.
Timer_B with seven compare registers and shadow registers carries the PWM for a three phase stage, and the 12 bit converter sequences on the same timer through its trigger input. That arrangement keeps the sample point at a fixed position in the switching period, which removes the switching ripple from the measurement without a filter.
The supply range reaches down to 1.8 V, but the converter and the internal reference have their own minimum. A board that runs the core at 1.8 V and expects 12 bit conversions at that rail is outside the specified condition, and the reference has to be checked against the actual supply at end of battery life.
Where this order code fits
Data loggers that buffer a conversion sequence, instruments with a display and a serial protocol running together, and control boards whose firmware is expected to be extended after the first release are the boards that choose this code over the 8 KB member. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.
Questions buyers ask
Is this code a drop-in for MSP430F133IPM? Yes. Same 64-pin body, same peripherals, double the flash and double the RAM. Firmware written for the smaller part runs unchanged and gains buffer space.
What is the ADC sequence length limit? Eight external channels plus internal temperature and supply channels, with autoscan and a transfer controller that writes results to memory. The 512 bytes of RAM sets how many results can be held.
Does the larger flash change the current? No in any practical sense. Active current is quoted at 280 microamps per megahertz for the family, and the memory size does not move that figure outside its spread.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.