MSP430AFE253IPW
Product Specifications
MSP430AFE253IPW
Texas Instruments — Power Management & Signal Chain
Product Overview
The MSP430AFE253IPW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
MSP430AFE253IPW: metering microcontroller with three 24 bit sigma delta converters and 16 KB flash in a 24-pin TSSOP
MSP430AFE253IPW is the three channel member of the metering family, with 16 KB of flash for a full tariff and communication stack in a TSSOP body of 24 pins. Three independent 24 bit sigma delta converters on one die is what separates this code from the two channel part beside it, and the flash doubles to 16 KB as well. Everything else matches the family: 512 bytes of RAM, a clock up to 12 MHz, 11 I/O pins, a 16 by 16 hardware multiplier and a 24-pin TSSOP body that stays small enough for a meter terminal block.
Order code and package
| Order code | MSP430AFE253IPW |
| Function | metering microcontroller with three sigma delta converters |
| Package | TSSOP, 24 pins, body code PW |
| Flash | 16 KB |
| RAM | 512 bytes |
| Converters | three independent 24 bit sigma delta, channels A0, A1 and A2 |
| Gain | 1, 2, 4, 8, 16 and 32 |
| Supply range | 1.8 V to 3.6 V |
| Clock | up to 12 MHz |
| I/O | 11 pins |
| Datasheet | SLAS736, shared with the two channel and one channel members |
Electrical parameters that decide the application
| Active current | 220 microamps at 1 MHz from 2.2 V |
| Standby current | 0.5 microamps |
| Off current | 0.1 microamps with RAM retained |
| Wake up time | under 1 microsecond |
| Converter count | three, each with its own differential input pair |
| Reference | internal, buffered output available externally |
| Flash advantage over AFE232 | 16 KB against 8 KB, which holds a tariff engine and a protocol stack |
| Multiplier | 16 by 16 hardware |
| Supply supervision | brownout and programmable supply voltage supervisor |
| Serial | one USART, UART or SPI |
Points to check before this part goes on a BOM
Three converters on three phases sample at one instant, so the sum of the three instantaneous products is total power with no time skew between phases. A sequential converter arrangement needs a correction term for the delay, and that term drifts with the clock, which is exactly the kind of error that shows up as a seasonal billing dispute rather than as a bench failure.
16 KB of flash is what makes a tariff engine possible. Time of day rates, a load profile in non volatile memory, an optical port protocol and a security layer do not fit comfortably in 8 KB, and the information segments keep calibration and tamper counters separate from the application so an update does not wipe the meter history.
The gain range stops at 32, which sets the smallest shunt signal the converter sees well. A 200 microohm shunt at 5 A gives 1 mV, and at a gain of 32 that is 32 mV into a converter whose input range is set by the gain and the reference, so the analog front end is built around the current range rather than around the 24 bit word.
Three converters plus the reference draw more than the two channel part, and the difference appears in the measurement burst rather than in the standby figure. The average current of a complete meter is dominated by the display and the communication port, not by the converters, which is why the 0.5 microamp standby matters more than the active number.
The 11 I/O pins have to carry three analog pairs, which leaves five pins for a pulse output, an optical port and a display segment driver. A product with a full segment display uses an external driver, and a product with an LCD driver on the die belongs on a different family.
The internal reference is shared by all three converters, so the ratio between phases stays tight even when the absolute gain moves with temperature. That is the property that matters for a three phase meter, where the quantity being billed is a sum and a common gain error cancels in part.
Where this order code fits
Three phase energy meters, three channel power quality monitors and motor power measurement on inverters use this code, because three current channels plus a shared voltage reference cover a three wire or four wire service without an external multiplexer. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the MCU Cross Reference page.
Questions buyers ask
Does this code cover a four wire three phase service? Yes. Three current channels and one voltage channel, or three voltage and three current with an external multiplexer, are the usual arrangements, and the three converters make the first case direct.
What is the difference from MSP430AFE232? One more converter and twice the flash, in the same 24-pin body. The core, the clock, the RAM and the peripheral set are otherwise identical.
Why is the standby current so important here? Because a meter spends most of its life with the converters off. 0.5 microamps in low power mode 3 and a wake in under a microsecond set the average current that the utility sees over a month.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.