Contact Us

MSP430AFE232IPW

Brand: Texas Instruments
Texas Instruments MSP430AFE232IPW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MSP430AFE232IPW — Power Management & Signal Chain | Superb Automation

MSP430AFE232IPW

Texas Instruments — Power Management & Signal Chain

Product Overview

The MSP430AFE232IPW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MSP430AFE232IPW: metering microcontroller with two 24 bit sigma delta converters in a 24-pin TSSOP

MSP430AFE232IPW is a 16 bit microcontroller with two independent 24 bit sigma delta converters and differential programmable gain inputs in a TSSOP body of 24 pins. The AFE2x2 devices carry two independent 24 bit sigma delta converters, each with a differential input and a programmable gain amplifier, on the same 16 bit core used across the MSP430 line. This code has 8 KB of flash, 512 bytes of RAM, a 16 MHz capable clock, 11 I/O pins and a 24-pin TSSOP body. Active current is 220 microamps at 1 MHz, lower than the general purpose F13x parts because the core runs with a smaller peripheral set.

Order code and package

Order codeMSP430AFE232IPW
Functionmetering microcontroller with two sigma delta converters
PackageTSSOP, 24 pins, body code PW
Flash8 KB
RAM512 bytes
Converterstwo independent 24 bit sigma delta, differential inputs A0 and A1
Gain1, 2, 4, 8, 16 and 32 through the input amplifier
Supply range1.8 V to 3.6 V
Clockup to 12 MHz system clock, internal calibrated frequencies
I/O11 pins
DatasheetSLAS736, MSP430AFE2xx family

Electrical parameters that decide the application

Active current220 microamps at 1 MHz from 2.2 V
Standby current0.5 microamps in low power mode 3
Off current0.1 microamps with RAM retained
Wake up timeunder 1 microsecond from standby
Converter resolution24 bit, with an oversampling ratio programmed per channel
Referenceinternal reference, plus a buffered output for external use
Multiplier16 by 16 hardware multiplier
Supply supervisionbrownout and a supply voltage supervisor with programmable level
Serialone USART, UART or SPI
Timerone 16 bit Timer_A with three capture and compare registers

Points to check before this part goes on a BOM

Two converters means voltage and current are sampled on the same clock edge. Real power is the average product of the two instantaneous samples, so simultaneous conversion removes the phase error that a sequential converter introduces at low power factor, where a one degree shift becomes a measurable billing error.

The gain stages go from 1 to 32 in powers of two, and the full scale input falls with the gain. A shunt with a 50 microvolt per amp output at 20 A gives 1 mV, which at a gain of 32 is 32 mV into the converter, so the resolution comes from the gain and not from the 24 bit word alone. A 24 bit converter at gain 1 with a 1 mV signal still only sees a small part of its range.

The internal reference has a temperature coefficient that lands directly on the measurement, and metering circuits usually calibrate against it at two temperatures rather than trusting the nominal value. The reference output is buffered and can be used by the external analog front end, which keeps the reference and the converters on the same drift.

Standby at 0.5 microamps and a wake in under one microsecond is what allows a meter to run a display and a real time clock while the converters are off. The measurement itself is a burst of a few hundred milliseconds per mains cycle, so the average current of a complete meter is far below the 220 microamps per megahertz figure.

The 11 I/O pins are the practical constraint. Two converter channels use four analog pins, leaving seven for a display, a pulse output and an optical port, and the USART shares two of them. A product with a segment display and an IrDA port fills the package, which is why the higher pin count AFE parts exist for three phase meters.

The converters are sigma delta, so the input is a sampling network and not a buffered amplifier. A source impedance above a few kilohms interacts with the sampling capacitor and produces a gain error that looks like a calibration drift, and the usual cure is a series resistor with a capacitor at the pin.

Where this order code fits

Single phase and split phase energy meters, power monitoring modules and shunt based current measurement boards use this family, because two converters measure voltage and current at the same instant and the product of the two samples is real power without a phase correction in firmware. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the MCU Cross Reference page.

Questions buyers ask

How is this different from MSP430AFE253? Channel count and flash. This code has two 24 bit converters and 8 KB of flash, the AFE253 has three converters and 16 KB, and both use the same 24-pin TSSOP body and the same core.

Can it measure three phase power? Not directly. Two converters cover one voltage and one current, or two currents with a shared voltage. A three phase meter needs three current channels and belongs on the AFE253.

What sets the measurement accuracy? The external shunt or current transformer, the internal reference drift and the gain stage. The 24 bit word length is not the limit at typical shunt levels, the analog front end is.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.