LP2998MRX-NOPB
Product Specifications
LP2998MRX-NOPB
Texas Instruments — Power Management & Signal Chain
Product Overview
The LP2998MRX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LP2998MRX-NOPB: DDR termination regulator in the 8-pin SO PowerPAD body at 43 C per watt
LP2998MRX-NOPB is the same DDR termination regulator as the SOIC code, in the thermally enhanced body that carries the 1.5 A rating in a SO PowerPAD body of 8 pins. MRX is the SO PowerPAD body, 4.89 mm by 3.90 mm with an exposed pad on the underside, and the difference from the SOIC code is thermal rather than electrical: 43 C per watt against 151 C per watt for the same die. That single number is what makes the 1.5 A continuous rating usable, because 1.35 W of pass stage loss becomes a 58 C rise instead of a 204 C one.
Order code and package
| Order code | LP2998MRX-NOPB |
| Function | linear VTT termination regulator with a buffered VREF output |
| Package | SO PowerPAD, 8 pins, body code DRB |
| VTT current | 1.5 A continuous, transient peaks to 3 A |
| Thermal resistance | 43 C per watt with the pad soldered to a copper area |
| Pad | exposed thermal pad on the underside, which is the only low resistance heat path |
| VDDQ floor | 1.35 V, covering DDR3L termination |
| VTT set point | VDDQ divided by two from two internal 50 kilohm resistors |
| VREF output | buffered VDDQ divided by two, active while VTT is tri-stated |
| Shutdown | active low, VTT high impedance, VREF unaffected |
| Junction range | minus 40 to plus 125 C |
| Datasheet | SNVS521 revision K, shared with the SOIC code and the LP2998-Q1 |
Electrical parameters that decide the application
| VTT at VDDQ 1.8 V, no load | 0.874 V to 0.939 V |
| VTT at VDDQ 1.8 V, plus or minus 0.5 A | 0.870 V to 0.940 V |
| VTT at VDDQ 1.35 V, no load | 0.656 V to 0.698 V |
| VTT at VDDQ 1.35 V, sinking 0.2 A | 0.641 V to 0.694 V |
| VREF at VDDQ 1.8 V | 0.887 V to 0.937 V |
| VREF output impedance | 2.5 kilohm |
| Thermal resistance comparison | 43 C per watt here, 151 C per watt in the SOIC body |
| Thermal rise at 1.35 W | 58 C here, 204 C in the SOIC body |
| Current density in the pad | the exposed pad is the return path for the pass stage, so vias under it carry the load current |
| ESD rating | 1000 V human body model, and the Q1 code adds the AEC-Q100 H1C classification |
Points to check before this part goes on a BOM
The pad is the part. Soldered to a copper area with a via field, 1.35 W of loss is a 58 C rise and the 1.5 A figure holds with a 70 C ambient. Left floating, the same package behaves like a small SOIC and the current has to come down to the value the plastic alone can carry, so a footprint change that drops the pad is a current change.
At 1.8 V memory the pass stage sees 0.9 V across it, so continuous current and internal loss move together. A DDR3L bus at 1.35 V halves that difference to 0.675 V and roughly halves the loss at the same current, which is why the same body supports more current on a 1.35 V bus than on a 1.8 V one.
Transient capability of 3 A is a pulse rating tied to the output capacitor. The datasheet is explicit that the package cannot dissipate a sustained 3 A, so the bulk capacitor on the termination plane has to carry the fast part of a DIMM switching event while the regulator catches up.
Thermal shutdown tri-states VTT rather than latching the part off, and it releases when the junction falls back through the hysteresis point. A board that hits that state during a memory stress test will show corrupted reads for as long as the junction stays hot, so the pad copper is a functional requirement and not a nicety.
MRX packing is tape and reel, and NOPB means the body is lead free without a declared tin-lead option. The electrical table in the datasheet is shared with the SOIC code and the LP2998-Q1, so a quotation that quotes a number from that table has to say which body the number was measured in.
Where this order code fits
Graphics cards, FPGA and DSP boards that carry several DDR3 devices, and compact industrial computers where the memory bus is close to the regulator, are the boards that use this body, because the pad solders to a copper area under the package and the heat leaves through the board. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is MRX electrically different from MAX? No. Same die, same electrical table, same pinout. The difference is the exposed pad and the 43 C per watt figure that comes with it, which changes the current the package can hold continuously.
Can the pad be left unsoldered on a low current board? It will regulate at low current, but the thermal margin goes away and the part behaves like the SOIC body. The pad also carries the ground return of the pass stage, so the connection is electrical as well as thermal.
Does this code carry the automotive rating? No. The AEC-Q100 classification belongs to the LP2998-Q1 order code, which shares the PowerPAD body but is a separate part number with its own qualification paperwork.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.