LP2998MAX-NOPB
Product Specifications
LP2998MAX-NOPB
Texas Instruments — Power Management & Signal Chain
Product Overview
The LP2998MAX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LP2998MAX-NOPB: DDR termination regulator rated 1.5 A in an 8-pin SOIC body
LP2998MAX-NOPB is a linear termination regulator that sources and sinks current to hold a DDR bus at half its memory supply in a SOIC body of 8 pins. MA is the plain 8-pin SOIC body of the LP2998, and in that body the junction-to-ambient figure is 151 C per watt against 43 C per watt for the same die in the SO PowerPAD package. The part regulates VTT to VDDQ divided by two, follows DDR1, DDR2, DDR3 and DDR3L buses down to a 1.35 V VDDQ floor, and is rated 1.5 A continuous with transient peaks to 3 A, which is what a DIMM bus asks for while it is switching.
Order code and package
| Order code | LP2998MAX-NOPB |
| Function | linear VTT termination regulator with a buffered VREF output |
| Package | SOIC, 8 pins, body code D |
| VTT current | 1.5 A continuous, transient peaks to 3 A |
| VDDQ range | 1.35 V minimum for DDR3L up to 5.5 V on the analog rail |
| VTT set point | VDDQ divided by two, from an internal divider of two 50 kilohm resistors |
| VREF output | buffered VDDQ divided by two, stays active in shutdown |
| Shutdown pin | active low, tri-states VTT and keeps VREF alive |
| Topologies | DDR1, DDR2, DDR3 and DDR3L termination, SSTL-2 and SSTL-18 compliant |
| Thermal resistance | 151 C per watt in this SOIC body |
| Junction range | minus 40 to plus 125 C |
| Datasheet | SNVS521 revision K, December 2007 revised August 2014 |
Electrical parameters that decide the application
| VTT at VDDQ 1.8 V, no load | 0.874 V to 0.939 V |
| VTT at VDDQ 1.8 V, plus or minus 0.5 A | 0.870 V to 0.940 V |
| VTT at VDDQ 1.35 V, no load | 0.656 V to 0.698 V |
| VTT at VDDQ 1.35 V, sourcing 0.2 A | 0.667 V to 0.710 V |
| VTT at VDDQ 1.35 V, sinking 0.2 A | 0.641 V to 0.694 V |
| VREF at VDDQ 1.8 V | 0.887 V to 0.937 V |
| VREF output impedance | 2.5 kilohm, 30 microamp load step tested |
| Absolute maximum on AVIN | 6 V, with PVIN limited to AVIN |
| Package comparison | 43 C per watt in SO PowerPAD against 151 C per watt here |
| Automotive option | the AEC-Q100 H1C rating belongs to the LP2998-Q1 code, not to this one |
Points to check before this part goes on a BOM
151 C per watt is the number that sizes this order code. With PVIN at 1.8 V and VTT at 0.9 V, 1.5 A puts 1.35 W through the pass stage, which is a 204 C rise in the SOIC body, so the 1.5 A continuous rating is unreachable here without derating. Holding the rise near 100 C leaves about 660 mA, and that is the figure a board that cannot give the pad copper should be planned around.
The VTT window at 1.8 V is 0.870 V to 0.940 V, about 70 mV wide, centred on 0.905 V. SSTL-18 allows plus or minus 40 mV around 0.900 V, so this regulator spends essentially the whole system allowance on its own tolerance and the board has to accept that the termination voltage itself is the error source, not the load step.
Sinking and sourcing are not symmetrical. At VDDQ 1.35 V and 0.2 A the sinking window is 0.641 V to 0.694 V while the sourcing window is 0.667 V to 0.710 V, so the bus reads about 26 mV lower when the regulator is pulling current out of the termination resistors than when it is pushing current in.
Shutdown is not a full power down. The SD pin tri-states VTT and leaves VREF running so the memory can enter suspend to RAM, and the datasheet adds that VTT must not be driven above AVIN while the part is in that state, which matters on a board where a second rail can back-feed the bus.
VSENSE exists because the termination plane is long. Connecting the sense pin to the middle of the bus removes the IR drop between the regulator and the far end of the resistors, and the trace has to stay away from the memory devices because noise on it goes straight into the regulation loop. A 0.1 microfarad capacitor on VREF is the usual companion part.
VDDQ is the reference input and PVIN is the power input, and both come from the same memory supply on most boards. Splitting them lets the pass stage run from a higher rail to reduce dropout, but the arrangement raises internal loss, so on a board with 1.35 V memory the two pins are normally tied together.
Where this order code fits
DDR2 and DDR3 termination on industrial single board computers, FPGA boards and telecom line cards is where this code appears, and the choice between this body and the PowerPAD body is usually made by the copper area the board can give the pad rather than by the current in the specification. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does this code cover a DDR3L bus at 1.35 V? Yes. The VDDQ floor is 1.35 V and the tables are written at that point. A DDR4 bus at 1.2 V is below the floor and belongs on a different regulator.
How does MAX differ from MRX? Same die, different body. MAX is the plain SOIC at 151 C per watt and MRX is the SO PowerPAD at 43 C per watt, so the two codes carry the same electrical table and very different continuous current on a real board.
Is VREF able to feed the DIMMs directly? It is a buffered reference with a 2.5 kilohm output impedance intended for the chipset and the DIMM reference pins, with 0.01 to 0.1 microfarad of bypass. It is not a supply rail for termination resistors.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.