Contact Us

LM319AM

Brand: Texas Instruments
Texas Instruments LM319AM is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM319AM — Power Management & Signal Chain | Superb Automation

LM319AM

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM319AM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM319AM: the A grade dual high speed comparator in a fourteen pin small outline body

LM319AM is the dual high speed comparator of the LM119, LM219 and LM319 family in the fourteen pin small outline body, in the A grade, supplied in a 55 piece tube and guaranteed from 0 to plus 70 degrees. It is the part an engineer chooses when two comparators are needed on one die, when both have to switch in under 100 nanoseconds, and when the supply is a split rail rather than a single 5 volt logic rail.

The fourteen pin body is not padding. It brings out the positive and negative supply of each comparator separately, plus a ground pin, which is what lets one half work on a plus or minus 15 volt analogue rail while the other half drives a logic level output, and it is why this part cannot be replaced by two eight pin comparators without a board change.

What the A grade buys and what the fourteen pins carry

LM is the family prefix, 319 is the dual high speed comparator, A is the tightened offset grade, and M is the fourteen pin small outline body. The /NOPB suffix that appears on the current orderable rows marks the lead free body, and the rows are printed as active production at 55 pieces per tube with a level 1 moisture rating at 260 degrees.

The A grade is separated from the plain grade by the offset and the gain rows rather than by the response time. Both grades switch in 80 nanoseconds typical, and the A grade holds 1 millivolt typical and 2 millivolts maximum offset against 2 typical and 8 maximum on the plain part. On a zero crossing detector the difference is the width of the uncertainty band around zero, which is exactly what a phase measurement cares about.

Orderable codeLM319AM, printed as LM319AM/NOPB on the current rows
Channels2, independent supplies and ground brought out
BodySOIC, 14 pins
Carriertube, 55 pieces
Temperature window0 to plus 70 degrees
Moisture levellevel 1 at 260 degrees
Response time80 nanoseconds typical
Family documentSNOSBJ2B, first issued August 2000, revised January 2016

The electrical rows that separate the A grade

Offset voltage on the A grade is 0.5 millivolts typical and 1 millivolt maximum at 25 degrees, with 2 millivolts over the operating range. Offset current is 20 nanoamps typical and 40 maximum, and bias current is 150 nanoamps typical with 500 maximum. The plain grade prints 2 and 8 millivolts, 80 and 200 nanoamps, and 250 and 1000 nanoamps on the same rows, so the A grade is roughly a factor of two on current and a factor of four on offset.

Voltage gain is 20 volts per millivolt minimum and 40 typical on the A grade against 8 minimum on the plain part, which is the row that decides how much of the offset the loop around the comparator can absorb. Saturation voltage is 0.75 volts typical and 1.5 maximum at 25 milliamps of sink, and output leakage is 0.2 microamps typical with 10 microamps maximum over temperature.

Input offset voltage at 25 degrees, A grade0.5 millivolts typical, 1 maximum
Input offset voltage over the range, A grade2 millivolts maximum
Input offset current, A grade20 nanoamps typical, 40 maximum
Input bias current, A grade150 nanoamps typical, 500 maximum
Voltage gain, A grade20 volts per millivolt minimum, 40 typical
Response time80 nanoseconds typical
Input voltage range on plus or minus 15 voltsplus or minus 13 volts
Differential input voltage, absolute maximumplus or minus 5 volts
Positive supply current at plus or minus 15 volts8 milliamps typical, 12.5 maximum
Negative supply current at plus or minus 15 volts3 milliamps typical, 5 maximum

Supplies, ground and the 16 volt limit

The document carries one warning that is easy to skip: do not operate the device with more than 16 volts from ground to the positive supply. The comparator works on a split rail of plus or minus 15 volts, or on a single 5 volt rail, and the ground pin sits at the midpoint of the split rail. A board that floats the ground pin at 24 volts and calls the rail plus or minus 15 is outside the absolute maximum even though each rail looks correct.

Positive supply current is 8 milliamps typical and 12.5 maximum at plus or minus 15 volts, negative supply current is 3 to 5 milliamps, and on a single 5 volt rail the positive current is 4.3 milliamps. Two comparators in a fourteen pin body drawing 11 to 17 milliamps total is a real load for a small linear regulator, and the decoupling has to sit close to the device rather than at the edge of the board.

Where an 80 nanosecond dual comparator earns its place

The usual application is a window detector on a fast analogue signal, or a zero crossing detector feeding a timer, in an instrument that already has a plus or minus 15 volt rail. The dual package keeps the two thresholds on one die at one temperature, which removes the drift difference that two separate comparators would introduce between the upper and lower limits of a window.

The window detector is worth describing because it is where the A grade pays for itself. Two comparators, one fed from a divider above the signal and one below, drive a wired OR node, and the window is the difference between their thresholds. With 1 millivolt maximum offset on each half the window is accurate to about 2 millivolts before the divider tolerance is counted, and with the plain grade's 8 millivolts the window is uncertain by 16. On a 1 volt window that is 1.6 percent against 0.2 percent, which is the difference between a part that needs trimming and one that does not.

The differential input is limited to plus or minus 5 volts absolute maximum, which is much lower than the supply, so a signal that can swing the full rail has to be attenuated before it reaches the input. That is the most common way this part is damaged in the field, and the fix is a series resistor plus a pair of clamp diodes, not a larger supply.

The tube, the grade and the second source question

The 55 piece tube is the carrier of a part that is usually bought in hundreds rather than in thousands, and the level 1 moisture rating means no bake before use. When the quantity grows the reel body carries 2500 pieces on the same fourteen pin outline, and the part marking changes with the carrier rather than with the silicon.

The second source question for this part is harder than for the eight pin comparators, because the fourteen pin pinout with separate supplies is less widely copied. Our pin to pin cross reference page sets out which alternatives share the fourteen pin footprint and which need a board change, and the obsolete part cross reference hub carries the family notes for the grades that have been withdrawn.

Questions that come with this code

Is the A grade worth the difference? On a window detector with a 1 millivolt window, yes. On a zero crossing detector driving a counter, the plain grade is usually enough and the offset only shifts the crossing point.

Can the two halves run on different supplies? The fourteen pin body brings out the supply pins of each comparator separately, so a split supply on one half and a single 5 volt rail on the other is possible inside the 16 volt ground to supply limit.

What replaces it if the grade is unavailable? A pair of eight pin comparators with the same 80 nanosecond response, at the cost of two packages and two offset windows that drift independently. Our amplifier cross reference page lists the candidates by response time and supply range.