LM293ADR
Product Specifications
LM293ADR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM293ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM293ADR: the A grade dual comparator on a 2500 piece reel
LM293ADR is the same A grade dual differential comparator as the tube string, on a large tape and reel, guaranteed from minus 25 to plus 85 degrees. Nothing about the silicon changes between the two carriers. The change is who the part is for: a reel is what a line with an automatic feeder orders, and a tube is what a bench orders.
The reel for this body is a 330 millimetre carrier with 12.8 millimetre tape, a 6.4 by 5.2 millimetre pocket 2.1 millimetres deep, and an 8 millimetre pitch. Those four numbers decide whether the part drops into an existing feeder program or needs a new one, and they are the first thing to check when a substitute is being considered.
The string, decoded
LM is the family, 293 is the dual comparator with the minus 25 to plus 85 window, A is the tighter offset sort, D is the eight pin small outline body, and R is the reel. There is no G4 in this string, and the addendum prints the plain row with the lead finish marked as call the vendor rather than as a fixed finish, while the .A row of the same code carries nickel palladium gold.
| Orderable code | LM293ADR |
| Comparators per body | 2, independent |
| Body | SOIC, 8 pins |
| Carrier | large tape and reel, 2500 pieces |
| Reel diameter | 330 millimetres |
| Tape width | 12.8 millimetres |
| 6.4 by 5.2 millimetres, 2.1 millimetres deep | |
| Pitch | 8 millimetres |
| Offset at 25 degrees | 1 millivolt typical, 2 maximum |
| Offset over the window | 4 millivolts maximum |
| Temperature window | minus 25 to plus 85 degrees |
| Supply voltage | 2 to 36 volts |
| Response time | 1.3 microseconds typical |
| Output | open collector, 6 milliamps sink minimum |
What the A sort changes on a production line
A test limit is written against the worst case part that can arrive. With the plain grade the offset maximum is 5 millivolts at room and 9 over the window, and every threshold test on the line has to allow for that. With the A sort the numbers are 2 and 4, so the limit can be tightened or the same limit can be held with more margin against a good board failing.
On a window detector the effect doubles, because both comparators in the package contribute. Two plain grades can put 18 millivolts between the nominal and the actual window edges over temperature, and two A sorts put 8. On a battery monitor that is the difference between a warning that fires at the right cell voltage and one that fires a hundred millivolts early.
The A sort also makes a calmer production line. A tighter part means a tighter distribution of measured thresholds, which means fewer boards sitting near the test limit and fewer retests. The price difference between the sorts is small enough that the retest saving on a few thousand boards usually pays for it.
Reel handling and the count that has to reconcile
A 2500 piece reel is a single traceability unit. Every board build consumes a known number, the reel label carries the date code, and the arithmetic at the end of the build either closes or raises a question. That is the practical reason a reel is preferred over cut tape on a line with a feeder: the count is the label, not a hand count.
Two handling points apply to this body. The moisture rating is level 1 at 260 degrees, so no bake is required, and the finish on the .A row is nickel palladium gold, which solders cleanly after long storage. Neither point survives a reel that is left on the machine over a weekend in a humid plant, so the storage rule is about the room rather than the bag.
Feeder setup is the other cost. The 12.8 millimetre tape and 8 millimetre pitch are common to the eight pin small outline family, so the same feeder and the same nozzle usually cover every variant on the board, including the plain grade and the A sort. That is why a bill of materials with both sorts on it is more expensive in paperwork than in machine time.
Where the reel string sits in a sourcing plan
The realistic pattern is one reel per year for a moderate build, released against a schedule rather than all at once. A build of 2000 boards consumes less than one reel, so the second build is served from the remainder unless the schedule is dense. That is where a count that does not reconcile becomes expensive: the parts exist, but the record does not prove it.
Our kitting service page describes how a reel is counted, labelled and issued against a build, and the date code management page covers what is recorded per reel so that a customer audit can follow a board back to a carrier.
There is one more use for this string that is worth naming. When a customer's drawing names the tube code and the line runs a reel, the two codes are the same part and the substitution is a carrier change, not a part change. That is the easiest approval in a bill of materials review, and it is the one to take first when a line is short.
Tape, pocket and the feeder setup
The 12.8 millimetre tape on this body is narrower than the 16.4 millimetre tape used on some of the fourteen pin parts, so a line that runs both bodies needs two feeder settings even though the pocket depth is the same 2.1 millimetres. That is worth checking before a first build rather than during it, because the symptom of a wrong tape width is a pick that misses by half a millimetre and a nozzle that wears on one side.
The 6.4 by 5.2 millimetre pocket leaves a small margin around an eight pin body, which is why the part sits flat and why a reel that has been stored on its side can present a tilted part at the first pick. Reels stored upright on a rack do not show the problem, and reels stored in a box on the floor often do.
What a partial reel costs
A partial reel is not free stock. It occupies a feeder position, it carries a date code that ages, and it needs a count before it can be issued to a second build. On a part at this price the carrying cost of a partial reel usually exceeds the value of the parts on it after about a year, which is why the sensible policy is to consume the remainder on the next build rather than hold it for a rainy day.
The exception is a service spares pool, where a partial reel is exactly what is wanted, because the quantities are small and the alternative is a cut tape with no carrier. Keeping one partial reel for service and consuming full reels on production is the arrangement that reconciles most easily at audit.
One more figure belongs in the record. The 2500 piece reel at the 6.4 by 5.2 millimetre pocket is a standard carrier, so a spare partial reel can be used to seed a new line without buying a second full reel. That is the cheapest way to cover a short build, and it is the only way to cover one when the lead time on a fresh reel is longer than the build window.
Questions that come with this code
Is the reel quantity always 2500? The addendum prints the large reel row at 2500 for this body, and the tape data table prints the same figure, so a different count is a repack and should be declared.
Can the plain grade be used instead? Only if the threshold budget can absorb 9 millivolts over the window instead of 4, and the pinout and the electrical shape are otherwise the same.
Does the reel fit a standard 8 millimetre feeder? The pitch is 8 millimetres and the tape is 12.8 wide, so yes, the same feeder as the rest of the small outline parts on the board.
What is the difference between this row and the .A row of the same string? The .A row is a revision level in the addendum with the finish printed explicitly, and both are active on the same reel size.