LM258DR
Product Specifications
LM258DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM258DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM258DR: the extended temperature dual op amp on a production reel
LM258DR is the dual operational amplifier of the LM158, LM258 and LM358 family in the eight pin small outline body, on a 2500 piece reel, guaranteed from minus 25 to plus 85 degrees. It is the grade that sits between the military window of the LM158 and the commercial window of the LM358, and it is the one that most industrial boards settle on because it costs almost nothing over the commercial part.
The family document has been revised for nearly fifty years and now covers fourteen orderable variants across four temperature grades, two supply ceilings and two silicon generations. The practical value of that is a pinout that a dozen second sources share, which is why the part survives on boards where the rest of the signal chain has moved on.
What follows is the detail a distributor page leaves out: which rows the temperature suffix actually changes, how the input stage behaves near the rails, what the output can and cannot drive, and what the reel code tells a line that is about to kit the part.
What the string and the grade declare
LM is the family prefix, 258 is the dual amplifier in the minus 25 to plus 85 degree grade, D is the eight pin small outline body, and R is the tape and reel carrier. The A suffix, when it appears, is the tightened offset grade rather than a different circuit, and it is worth naming explicitly on a purchase order because the two are not interchangeable on a threshold budget.
The temperature grade is the part of the string that changes behaviour. The same die is sold as the LM158 from minus 55 to plus 125 degrees, as the LM258 from minus 25 to plus 85, and as the LM358 from 0 to plus 70. Each grade carries its own table, and the numbers are guaranteed rather than typical, which is why a board qualified on the LM358 cannot simply be uprated to the LM258 without re-reading the offset row.
| Orderable code | LM258DR |
| Channels | 2 |
| Body | SOIC, 8 pins |
| Carrier | tape and reel, 2500 pieces, 330 millimetre reel, 12.4 millimetre tape |
| Temperature window | minus 25 to plus 85 degrees |
| Lead finish | nickel palladium gold, level 1 moisture rating at 260 degrees |
| Supply ceiling, absolute maximum | plus or minus 16 volts, or 32 volts single supply |
| Family document | SLOS068AB, first issued June 1976, revised October 2024 |
The rows the 258 grade prints for itself
Offset voltage for the plain grade is 3 millivolts typical and 5 millivolts maximum at 25 degrees, widening to 7 millivolts across minus 25 to plus 85. The A grade prints 2 millivolts typical, 3 maximum at room temperature and 4 over the window, with a drift of 7 microvolts per degree typical and 15 maximum. On a chain that measures a 10 millivolt shunt the plain grade is adequate, and on a chain that resolves 2 millivolts it is not.
Input bias current is minus 20 nanoamps typical and minus 150 maximum for the plain grade, reaching minus 300 over the window, and offset current is 2 nanoamps typical with 30 maximum at room temperature. Those numbers are what limit the source impedance. A 1 megaohm source with 150 nanoamps of bias current sits 150 millivolts off before the offset is even considered, so the divider that feeds the input belongs in the low kilo ohm range on this grade.
| Input offset voltage at 25 degrees | 3 millivolts typical, 5 maximum |
| Input offset voltage over the window | 7 millivolts maximum |
| Offset drift | 7 microvolts per degree typical |
| Input bias current | minus 20 nanoamps typical, minus 150 maximum |
| Input offset current | 2 nanoamps typical, 30 maximum |
| Common mode range | to within 1.5 volts of the positive rail |
| Large signal gain | 50 volts per millivolt minimum, 100 typical |
| Gain bandwidth product | 0.7 megahertz |
| Slew rate | 0.3 volts per microsecond |
| Quiescent current per amplifier | 350 microamps typical, 600 maximum |
Why the input range stops below the positive rail
The common mode range reaches the negative rail and stops about 1.5 volts below the positive rail, which is the signature of the PNP input pair this family uses. A sensor that swings to the top of a 5 volt rail will therefore leave the amplifier in a region where the output is undefined, and the usual fix is either a rail to rail part or a divider that keeps the signal inside the window.
Below the negative rail the story is different: the input pair tolerates the signal going under the rail without phase inversion on most members of this family, but the document does not promise it as a linear region, so a circuit that relies on it is relying on a typical curve. The honest approach is to clamp the input or to add a series resistor, and the series resistor then interacts with the bias current as described above.
There is one more input detail that a circuit reader should note. The differential input can be taken to plus or minus 32 volts absolute maximum, which is well inside the supply ceiling and far outside the linear range. That gap is what makes the part survive a signal that is present while the supply is off, and it is also what makes an input clamp worth the two diodes on a board that connects to a field cable.
What the output can drive and what it cannot
The output swings to within 5 to 20 millivolts of the negative rail into a 10 kilo ohm load at 5 volts, and stops 2 to 3 volts below a 30 volt positive rail into the same load. That asymmetry is worth remembering: the part sinks well and sources poorly at high supply voltages, so a load that returns to the positive rail is a harder job than one that returns to ground.
Short circuit current is plus or minus 40 to 60 milliamps, and the output survives an indefinite short to ground at 25 degrees when the supply is 15 volts or less. Above that the dissipation in the output stage rises, and the absolute maximum table warns that a short to the supply rail can destroy the device. Driving a capacitive load directly is the other common mistake: 100 picofarads is fine, and a 10 nanofarad cable needs a series resistor of 50 to 100 ohms to keep the loop stable.
The reel, the kitting step and the date code
The reel carries 2500 pieces on a 330 millimetre carrier with 12.4 millimetre tape, and the moisture rating is level 1 at 260 degrees, so no bake is needed before the feeder. For a line that kits several hundred boards a day, one reel covers the week and the date code is recorded once, which keeps the traceability record short.
For a build of twenty prototypes the reel is the wrong carrier: a partial reel is not returnable, the feeder setup costs more than the parts, and the tube body, which the same addendum lists at 50 pieces, is the practical order. Our amplifier cross reference page lists the dual and quad members that share this pinout across the four grades, and the date code management page shows how we record a reel that is carried across two builds.
Questions that come with this code
Can the LM258DR replace an LM358 in an existing board? Usually yes, because the pinout and the supply ceiling are the same, and the difference is the wider guaranteed window and a slightly tighter offset. The reverse move, from 258 to 358, narrows the window and is the one that needs a review.
Is the A grade worth the extra line? It buys 2 millivolts off the maximum offset and halves the drift, which matters when the amplifier is the first stage of a measurement and not when it is a buffer behind a digital signal.
What limits the supply to 32 volts? The absolute maximum table, and the recommended range is lower in practice once the output swing is taken into account. Our pin to pin cross reference page carries the grade table for this family so that a swap is checked against the offset and the window rather than against the pinout alone.