DRV8320HRTVR
Product Specifications
DRV8320HRTVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8320HRTVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8320HRTVR: a 60 V gate driver with the configuration done by resistors
The DRV8320HRTVR is the hardware variant of the DRV8320, the 60 V member of the DRV832x family. It does not contain power FETs. It contains three half-bridge gate drivers, a charge pump for the high side, a linear regulator for the low side, and a resistor configurable interface that replaces the SPI port of the S variant. The point of the part is to drive six external N-channel MOSFETs of whatever current class the application needs, from a 6 V to 60 V rail, while keeping the gate drive, the dead time and the protection inside one 5 mm by 5 mm package.
Peak gate current is adjustable from 10 mA to 1 A source and 20 mA to 2 A sink. That range covers a small 30 V FET with 3 nC of gate charge and a large 100 A FET with 150 nC, and the IDRIVE pin picks one of seven settings with a resistor, so a board can be retuned for a different FET without a code change or a new board for the driver section.
The charge pump regulates to VM plus 11 V and supports 25 mA of average gate charge current. Below 12 V of VM it runs in full doubler mode and produces twice VM minus 1.5 V unloaded, which is what lets the part hold the high-side FET on at 100 percent duty instead of forcing a refresh window every cycle. The low side runs from an internal 3.3 V linear regulator that also feeds external analog loads at up to 30 mA on DVDD.
This member carries no current sense amplifiers and no buck regulator. The comparison table in the vendor document is explicit: DRV8320 and DRV8320H have zero shunt amplifiers and no buck, DRV8320R and DRV8320RH add the 600 mA buck, DRV8323 and DRV8323H add three shunt amplifiers, and the R and S letters stack on top of those. Reading the code correctly is most of the work of buying the right part.
Key data for the DRV8320HRTVR
| Operating range | 6 V to 60 V on VM, gate driver supply from the same rail |
| Outputs | Three half bridges driving external N-channel FETs, high side and low side |
| Gate current | 10 mA to 1 A peak source, 20 mA to 2 A peak sink, seven settings on IDRIVE |
| Charge pump | Regulated to VM plus 11 V, 25 mA average, full doubler below 12 V |
| Duty cycle | 100 percent supported, no refresh window needed |
| PWM modes | 6x, 3x, 1x and independent inputs |
| Logic | 1.8 V, 3.3 V and 5.0 V CMOS inputs |
| Regulator | 3.3 V linear regulator, up to 30 mA on DVDD |
| Sleep current | 12 uA typical in low power sleep mode |
| Not fitted | No shunt amplifiers, no buck regulator on this variant |
Body, packing and marking data
| Body | 32-pin WQFN, the RTV outline, 5.00 mm by 5.00 mm, 0.75 mm maximum height |
| Carrier | 3000 pieces on a 330 mm large tape and reel, 250 pieces on a 180 mm small reel under the RTVT suffix |
| Finish | NIPDAU lead finish, moisture level 1, 260 C peak reflow with unlimited floor life |
| Temperature | Minus 40 C to plus 125 C operating |
| Marking | DRV8320H on the body, lot and date code on the reel label |
Reading the code before you buy it
DRV8320H breaks into DRV8320 for the circuit, H for the hardware interface, RTV for the 32-pin 5 by 5 body, and a trailing R for the large reel. Drop the trailing R and use a T instead and the same part arrives on a 250 piece small reel as DRV8320HRTVT. The two are the same silicon in the same body, so a pilot line can run on the small reel and a production line on the large one without a change to the stencil.
The trap is the pin count. The SPI version of the same circuit, DRV8320S, is published in a 40-pin RTA body at 6 mm by 6 mm, because the four SPI pins do not fit on the 32-pin outline. A buyer who treats DRV8320H and DRV8320S as interchangeable because the circuit name matches will receive a part that does not land on the pads. The footprint has to be chosen first, then the interface suffix.
One more detail sits in the addendum rather than in the features list. The 32-pin body carries no current sense amplifier, so a drive that needs three low-side shunts has to add external amplifiers or move to the 8323. That adds three op amps, their feedback networks and the board space around them, which is often more than the price difference between the two circuits.
Where the DRV8320HRTVR fits
This is the part for a drive stage that already exists as six discrete FETs and needs a gate driver that will not fight the board. E-bike controllers at 48 V, cordless garden tools at 36 V to 48 V, and pump and fan modules in the 24 V to 60 V band are the usual homes. The 60 V ceiling is what separates it from the 100 V DRV835x, and the difference matters on a 48 V battery pack that swings to 58 V at full charge with a regenerative spike on top.
Because the FETs are external, the current rating of the drive is set by the FETs, not by the driver. That is the reason this part turns up in 500 W tools and in 50 W fans with the same order code. What changes is the IDRIVE setting, the VDS trip point and the amount of copper under the FETs. A buyer who consolidates several drive boards onto one driver circuit is trading a part number for a resistor value, and our power management cross reference page is the place to check which of the family members share a footprint.
Industrial and logistics robots use the 1x PWM mode with an external hall sensor, because the driver can take a single PWM line and a direction from a low pin count controller. That mode is the reason the part shows up in small AGV wheel drives where the controller has more inputs than it has timers.
Questions we get on this code
Does the 60 V rating mean a 60 V battery is fine? It means the silicon survives 60 V at the pin with the specified behaviour. A 14 cell pack at 58.8 V full charge is inside the window but has almost no margin for the spike that a long motor cable produces when the bridge turns off into an inductive load, so the bulk capacitor and the TVS on that rail do real work.
Why is the sleep current 12 uA and not less? It is the price of keeping the charge pump monitor and the protection comparators alive so the part can wake without a full restart. A tool that sleeps for a year still sees tens of microamps, which is why the pack protection circuit has to cut the rail rather than rely on the driver.
Can the same board carry the 8323 for the sense amplifiers? Only if the board is built for the larger body. The 8323H is a 40-pin 6 mm by 6 mm part and the 8323RH is a 48-pin 7 mm by 7 mm part, so the answer is no across the 32-pin outline. That is a change to the board, which is why the sense decision has to be made before the first prototype.
What happens if a 100 V FET is used with a 60 V driver? The FET works, and the gate charge is usually larger, so the IDRIVE setting has to move up. The limit is the gate voltage, not the FET rating, and the charge pump will still hold the gate at VM plus 11 V. The failure mode to check is the gate oxide rating, since a 100 V FET with a 20 V gate limit is fine at a 60 V VM and would not be at 100 V.
Where does this part sit against the 8323RH when a customer is short of either? Both are 60 V circuits with the hardware interface, the difference is the three sense amplifiers and the buck. When a line is down and the exact suffix is not available, our BOM shortage recovery page walks through the substitution check that has to happen first.