LM239PW
Product Specifications
LM239PW
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM239PW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM239PW: the quad comparator in the TSSOP body, 2000 pieces on a twelve millimetre tape
LM239PW is the quad differential comparator in the fourteen pin TSSOP body, the narrow package that takes roughly half the board length of the SOIC part. The die is the same one used by LM239D, with the same four comparators, the same open collector outputs and the same input stage that reaches ground. What changes is the footprint, the thermal path and the tape that the line has to be set up for.
Package choice is usually made late, by whoever is fighting for board area, and it is usually made once. The TSSOP body saves about three and a half millimetres of length per package against the SOIC, which on a board with three of them is a centimetre of routing space, and it costs thermal resistance because the body is smaller and the lead frame has less copper.
This page covers the electrical rows so the page stands alone, then the body, the tape and the thermal question, which are the three things that decide between the two packages.
LM239PW as the vendor document publishes it
Figures are from revision Z dated May 2025, at a 5 volt supply unless the row says otherwise.
| Channels | 4, independent |
| Supply voltage | 2 to 36 volts, split rails to plus or minus 18 volts |
| Input offset voltage | 2 millivolts typical, 5 maximum at 25 degrees |
| Input offset voltage over temperature | 9 millivolts maximum, minus 25 to plus 85 |
| Input offset current | 5 nanoamps typical, 50 maximum |
| Input bias current | 25 nanoamps typical, 250 maximum |
| Common mode range | 0 to supply minus 1.5 volts at 25 degrees |
| Common mode range over temperature | 0 to supply minus 2 volts |
| Differential input voltage | plus or minus 36 volts |
| Large signal gain | 50 volts per millivolt minimum, 200 typical |
| Output low voltage | 150 millivolts typical, 400 maximum at 4 milliamps |
| Output low voltage over temperature | 700 millivolts maximum |
| Output sink current | 6 milliamps minimum at 1.5 volts |
| Output leakage | 0.1 nanoamps at 5 volts, 1 microamp at 30 volts over temperature |
| Supply current, four comparators | 0.8 milliamps typical, 2 maximum |
| Response time | 1.3 microseconds with 5 millivolts of overdrive |
| Response time, logic step | 0.3 microseconds |
| Operating temperature | minus 25 to plus 85 degrees |
| Package | 14 pins, TSSOP body PW, 0.65 millimetre pitch |
| Part marking | L239 |
| Carrier | 2000 pieces on a 330 millimetre reel for the R code |
The body: 0.65 millimetre pitch and what it costs in routing
The TSSOP body is 0.65 millimetre pitch against 1.27 millimetres on the SOIC. That halves the package length but it does not halve the routing: a 0.65 millimetre pitch leaves about 0.3 millimetres between pads, so a trace can pass between two pads only at the thinnest width the board house will accept, and most boards do not route between them at all.
On a four layer board with an inner layer available, the TSSOP is a clear win. On a two layer board the escaping traces from fourteen pins at 0.65 millimetre pitch become the routing problem, and the SOIC with its 1.27 millimetre pitch is often the faster board to finish even though it takes more length.
The part marking shrinks with the body as well. The TSSOP part is marked L239 rather than LM239, so an incoming inspection that reads the full code off the package will not find it. The marking and the reel label together are what an inspector has to work from, and the inspection plan should say so.
The tape: 12.4 millimetres against 16.4, and 2000 against 2500
The reel row for this body prints 2000 pieces on a 330 millimetre reel, a 12.4 millimetre tape width, a 6.9 millimetre pocket and 1.6 millimetres of depth. The SOIC part uses a 16.4 millimetre tape with a 6.5 millimetre pocket and 2.1 millimetres of depth, so the two packages need different feeders and different nozzle setups.
A line that already runs a 12.4 millimetre tape for another TSSOP part needs no new tooling, which is the usual reason a TSSOP appears on a board that was originally all SOIC. A line that has only ever run 16.4 millimetre tape will need a feeder change, and that change is worth discovering before the first build rather than during it.
The 2000 piece reel is also 500 pieces shorter than the SOIC reel. On a high volume line that is a reorder point change rather than a purchasing problem, but a planner who assumes parity between the two carriers will run short by 20 per cent on the first cycle.
Thermal: the smaller body runs hotter
The four comparators dissipate 0.8 milliamps at 5 volts, which is 4 milliwatts, and even at the 2 milliamp maximum it is 10 milliwatts. At that level the package thermal resistance barely matters, and a TSSOP body with 0.65 millimetre leads is comfortable at 85 degrees with no special copper.
The number changes when the outputs are loaded. Four outputs sinking 4 milliamps at 400 millivolts dissipate 6.4 milliwatts, and at the 700 millivolt worst case it is 11 milliwatts, so the package carries about 20 milliwatts in a heavy load case. The TSSOP junction to ambient is higher than the SOIC because the body is smaller, and the difference is enough to matter only when the ambient is already near the top of the window and the board is in a sealed enclosure.
For a comparator that drives four relays through transistors, the dissipation sits in the transistors rather than in the comparator, and the package choice is purely a board area question. For a comparator that drives four optocouplers directly, the dissipation sits in the comparator and the package choice should be checked with the thermal calculation.
Where the TSSOP quad belongs
It belongs on a dense board where four thresholds share a supply and the routing has an inner layer to escape into: a battery management board, a compact industrial controller, a medical analyser channel card, a telecom line card. It also belongs where the board is a drop in replacement for an existing board that already used the TSSOP outline.
It is the wrong choice on a two layer board with wide traces, on a board where the ambient is above 70 degrees with loaded outputs, and on a board where the inspector needs to read the full part number off the package. In those cases the SOIC body is the better answer even at the cost of length.
For the alternates that share this die and pinout, our pin to pin cross reference page lists the codes in the two bodies, and the drop in replacement verification page covers what to measure when a board moves from one body to the other.
Carrier rows and what to confirm
| LM239PW | TSSOP PW, 14 pins | tube | the tube quantity is read off the addendum at order time |
| LM239PWR | TSSOP PW, 14 pins | 2000 pieces, 330 millimetre reel | 12.4 millimetre tape, marking L239 |
| LM239D | SOIC D, 14 pins | tube | the wider body, 16.4 millimetre tape on the reel code |
| LM239ADR | SOIC D, 14 pins | 2500 pieces, 330 millimetre reel | A grade sort in the wider body |
The addendum printed with revision Z lists the LM239PWR reel row at 2000 pieces and does not print a row for the plain PW tube code in the same table, so the tube quantity should be confirmed with the supplier rather than assumed. Our one stop BOM sourcing page covers how a package change is quoted across a whole bill of materials.
Buying questions that come with this code
Is LM239PW the same die as LM239D? Yes. The package and the marking change, and the electrical rows are the same apart from the thermal path.
Can a SOIC footprint take the TSSOP part? No. The pitch and the body width differ, so the change is a board revision rather than a substitution.
Does the shorter part number on the package cause a receiving problem? It can, because the marking is L239 rather than LM239, so the inspection plan has to accept the short marking together with the reel label.