Contact Us

LM211QDR

Brand: Texas Instruments
Texas Instruments LM211QDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211QDR — Power Management & Signal Chain | Superb Automation

LM211QDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211QDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211QDR: the 125 degree grade of the strobed comparator

LM211QDR is the automotive temperature grade of the single strobed comparator, in the eight pin SOIC body, on tape and reel. The Q in the code is the minus 40 to plus 125 degree window, not an automotive qualification. The two are often confused on a purchase order, and the confusion is expensive when a programme expects an AEC-Q100 report that this string does not carry.

The base LM211 stops at 85 degrees. The Q grade extends the guaranteed window by 40 degrees at the top, and the data sheet prints separate limits for it rather than extrapolating the industrial rows. That distinction is the whole point of the part: a limit that is guaranteed over the wider window is a different promise from a typical curve that happens to look flat.

The applications that need it are the ones where the board sits next to a heat source: a motor drive heatsink, a power supply secondary, an under hood module, an LED driver enclosure. In each of those the ambient at the comparator is 20 to 40 degrees above the ambient of the box, and an 85 degree part has no margin left.

What the Q grade guarantees that the base grade does not

The offset voltage window is printed for the Q grade over the full minus 40 to plus 125 degree range, and the maximum is 4 millivolts on the Q rows against 3 millivolts at room temperature on the same die. In other words the wider guarantee is bought with a wider number, and a threshold chain that was trimmed to 1 millivolt at 25 degrees still holds, while a chain that relied on a 3 millivolt maximum over temperature does not.

Bias and offset currents widen in the same way. Bias current is 100 nanoamps maximum at room temperature and the Q rows carry their own ceiling at the hot end, where leakage roughly doubles for every ten degrees of junction temperature. At 125 degrees the input current is the parameter that decides whether a high impedance divider is usable at all.

Orderable codeLM211QDR
Grade letterQ, minus 40 to plus 125 degrees
Body and carrierSOIC, 8 pins, tape and reel
Offset at 25 degrees0.7 millivolts typical, 3 maximum
Offset over the Q window4 millivolts maximum
Bias current75 nanoamps typical, 100 maximum at 25 degrees
Response time115 nanoseconds low to high, 165 high to low
Supply current, positive rail5.1 milliamps typical, 6 maximum
Output rating50 volts, 50 milliamps, open collector and emitter

The temperature window measured at the comparator, not at the box

A 125 degree rating is a junction or ambient rating at the device, and the gap between that and the enclosure ambient is the thermal resistance of the path multiplied by the dissipated power. This part dissipates little, roughly 100 milliwatts on a plus or minus 15 volt supply, so the rise is a few degrees in still air and less on a board with copper under the body.

What does move is the local ambient. A comparator sitting 10 millimetres from a switching converter sees the converter's hot spot rather than the box temperature, and a comparator in a sealed aluminium enclosure sees the enclosure temperature after a two hour soak. Both are cases where the Q grade is the honest choice and the industrial grade is a hope.

The cold end has its own behaviour. At minus 40 degrees the input bias current falls, the offset stays inside its window, and the response time lengthens slightly. A threshold chain that is marginal at the cold end is usually marginal because the reference drifted, not because the comparator did.

Trimming an offset at 125 degrees

The balance pins trim the offset at the temperature where the trim is performed. If the trim happens at 25 degrees and the board runs at 110, the residual is the drift between those two points, bounded by the difference between the room temperature maximum and the over temperature maximum. On the Q grade that difference is about 1 millivolt, which is small enough to leave alone on a 100 millivolt threshold and large enough to matter on a 10 millivolt one.

For tight thresholds the practical answer is to trim at the operating temperature, in a chamber, with the board powered. That costs a chamber slot per unit and is only worth it on low volume instruments. On volume products the trim is replaced by a wider threshold window or by a comparator with a lower drift.

Strobe and balance pins at the temperature extremes

The strobe needs 3 to 5 milliamps and must not be shorted to ground. Over temperature the current window moves slightly, so a resistor chosen to deliver 3 milliamps at 25 degrees delivers less at 125, where the internal reference of the mirror drifts. Choose the resistor for the middle of the window, not the edge.

The balance potentiometer has its own drift, and at 125 degrees a carbon trimmer can move more than the comparator. A fixed resistor pair selected at test, or a digital potentiometer with a specified temperature coefficient, is the more honest solution on a board that runs hot.

Reading a hot ambient on the bench

A thermal survey is the only honest way to choose between the industrial grade and the Q grade. Put a thermocouple on the comparator body, run the product at full load inside its enclosure for two hours, and read the body temperature rather than the air temperature. The difference between the two is often 15 degrees in a sealed box.

If the body settles at 95 degrees the industrial part is outside its window and the Q grade has 30 degrees of margin. If it settles at 70 the industrial part is fine and the Q grade is money spent on nothing. That measurement costs half a day and settles a question that no paper comparison can.

The bench measurement also exposes the local gradient. A comparator 5 millimetres from a linear regulator sees a hot spot that the box average hides, so the thermocouple goes on the part and not on the lid.

Q grade, Q1 grade and the documents behind each

The Q suffix in this family is a temperature grade. It does not carry an AEC-Q100 qualification report, a production part approval file, or a change notification agreement. Those belong to the Q1 strings in the automotive catalogue, and this family's orderable addendum prints the Q rows but not a Q1 row for the same body.

That matters when a customer's drawing says automotive. A supplier that ships the Q grade against a Q1 requirement has made a paperwork substitution, and the audit will find it. The reverse substitution is harmless but more expensive.

Our defence grade components page covers the wider window parts used where the ambient is extreme but the automotive file is not wanted, and the power management cross reference page lists the family equivalents with their temperature grades side by side.

Buying questions that come with this code

Does the Q grade need a different board? No. Same eight pin body, same pinout, same footprint. The difference is the guarantee and the price.

Is the Q grade cheaper than the Q1 grade? Yes, usually by a wide margin, because the qualification file is not part of the price. It is the right part when the ambient is hot and the automotive file is not required.

How much does the offset drift per degree? The document gives a maximum over the window rather than a slope. The honest reading is 1 millivolt across the 100 degrees between the room temperature limit and the hot limit, which averages 10 microvolts per degree and is not a straight line.

Is the Q grade available in a tube? Yes, under the string without the R. The tube carries 75 pieces and suits a build of a few hundred boards.

What happens above 125 degrees? Nothing good. The part is not characterised there, and the failure mode at the top of the window is usually the input stage rather than the output. Use the LM111 grade or a different family if the ambient goes higher.