Contact Us

LM211DR

Brand: Texas Instruments
Texas Instruments LM211DR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211DR — Power Management & Signal Chain | Superb Automation

LM211DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211DR: the same strobed comparator on a 2500 piece reel

LM211DR is the reel carrier of the single strobed comparator, eight pins in the SOIC body, 2500 pieces on a 330 millimetre reel, guaranteed from minus 40 to plus 85 degrees. The die, the pinout and every electrical row are identical to the tube code. What changes is how the part arrives at the line, and that change decides feeder setup, moisture handling and the minimum order quantity a buyer should hold.

The reason a page exists for the reel code is that the carrier is the part a production planner actually signs off. A tube of 75 pieces disappears into a week of pilot builds and then the line needs a reel, and the move from tube to reel is often made in a hurry, in the middle of a build, without anyone checking that the tape width and the pocket depth match the feeder already on the machine.

The electrical summary below is repeated so that this page stands on its own, then the carrier, the moisture level and the reflow profile are treated as the subject rather than as a footnote.

LM211DR as the vendor document publishes it

Figures are from the vendor document revision K dated March 2017, at plus or minus 15 volts unless the row says otherwise.

Channels1
Supply5 to 30 volts single, or plus or minus 15 volts split
Input offset voltage0.7 millivolts typical, 3 maximum at 25 degrees
Input offset voltage over temperature4 millivolts maximum over minus 40 to plus 85
Input offset current4 nanoamps typical, 10 maximum
Input bias current75 nanoamps typical, 100 maximum
Common mode rangeminus 14.5 to plus 13 volts on a plus or minus 15 supply
Large signal gain40 volts per millivolt minimum
Output low voltage0.75 volts typical, 1.5 maximum at 50 milliamps
Output leakage0.2 nanoamps at 25 degrees, 0.5 microamps over temperature
Supply current, positive rail5.1 milliamps typical, 6 maximum
Supply current, negative rail4.1 milliamps typical, 5 maximum
Response time, low to high115 nanoseconds
Response time, high to low165 nanoseconds
Output rating50 volts, 50 milliamps
Strobe3 to 5 milliamps, current driven
Offset balancetwo pins, external potentiometer
Operating temperatureminus 40 to plus 85 degrees
Package8 pins, SOIC body D
Carrier2500 pieces on a 330 millimetre reel

What the reel changes on the line

A 330 millimetre reel of an eight pin SOIC runs on a 12.4 millimetre tape with a 6.4 millimetre pocket and 2.1 millimetres of depth. Those three numbers are what the feeder is set for, and a feeder set for an eight millimetre tape will not take the reel at all. The same 12.4 millimetre width is used across most of the eight pin SOIC family, so a line that already runs an eight pin analogue part usually needs no new tooling.

A 2500 piece reel is roughly a month of a single placement nozzle running one shift, which sets the reorder point rather than the purchase quantity. The practical number to plan against is the reorder point plus the lead time of the supplier, and for a part in this family the honest default is to hold two reels when the board is in volume, because a stockout costs more than the carrying cost of one extra reel.

The reel also fixes the date code question. Every piece on the reel is from one lot, so a traceability record that captures the reel label covers the whole build, and an incoming inspection plan can sample per reel instead of per board. That is the practical difference between a tube and a reel in a quality system, and it is not a small one.

Moisture level one, and what the reflow profile still has to respect

The vendor addendum prints moisture sensitivity level 1 with a 260 degree peak and unlimited floor life for the SOIC family. Level 1 means the part does not need a bake before reflow and does not need a dry cabinet, which removes a handling step that a level 3 part would require.

Unlimited floor life is not a licence to run any profile. The 260 degree peak with the standard ramp is what the level 1 rating is tied to, and a profile that spends longer above 240 degrees than the vendor's reference still changes the stress the package sees. For an eight pin body with a small die the risk is low, but a reflow recipe copied from a large BGA board should be trimmed before it is used here.

The strobe and balance pins on a production board

On a production board the balance pins are usually left open and the strobe is either tied to a fixed logic level through a resistor or left open. Leaving the balance pins open is correct: they are high impedance inputs to the input stage and floating them adds no error. The strobe must not be left floating if it is used, because the 3 to 5 milliamp current drive is a hard requirement and a floating pin can sit in the middle of its range.

Two production habits come out of that. The first is to tie the strobe to a test point rather than to a hidden via, so that a functional test can hold the output off while the next stage is probed. The second is to record which boards were strobed during test and which were not, because a build that mixes both leaves a failure mode that nobody can reproduce later.

If the strobe is not used at all, the document's default condition is for it to be open, and the comparator then behaves as a plain single comparator. An engineer who wants the output permanently enabled can leave the pin open rather than tying it to a rail, which is the lower risk of the two options.

Response time in a real circuit

The 165 nanosecond high to low figure is measured with a 500 ohm collector resistor to 5 volts and 5 picofarads of load. In a real circuit the load is the wiring plus the next gate, and a 1 kilo ohm pull up with 20 picofarads gives a 20 nanosecond time constant, which is small against 165 nanoseconds but not against the 115 nanosecond low to high figure.

The asymmetry between the two edges is a property of the output transistor rather than of the input stage, so a circuit that needs symmetrical timing should not use the falling edge as the timing reference. A 10 to 20 nanosecond difference is enough to matter in a time to digital converter and irrelevant in a relay driver.

Where the reel code belongs, and what to confirm

The reel code belongs on any line that places more than a few hundred boards a week, and in any build where the traceability record is per reel. The tube code stays on the approved list for repairs and for the engineering bench, because opening a 2500 piece reel for three parts is a waste of a lot label.

One caveat belongs on the purchasing file. The vendor addendum dated September 2026 prints only the automotive LM211QDRG4 row for the LM211 codes, and the plain DR row is not printed there. That does not mean the part does not exist, but it does mean a production order should be confirmed against stock and date code before the purchase order is released. Our date code management page covers what to record, and the BOM scrubbing page covers the alternates that sit behind this code.

Buying questions that come with this code

Is LM211DR the same part as LM211D? Electrically yes, and the only difference is the carrier. A board qualified with the tube code does not need requalification when the reel code arrives.

Does the reel require a bake before use? No. Level 1 with unlimited floor life, so the reel goes from the bag to the feeder.

Can a tube and a reel be mixed on one build? They can, because the die is the same, but the date code record then has two lots and the traceability record has to say so.