Contact Us

LM139DR

Brand: Texas Instruments
Texas Instruments LM139DR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM139DR — Power Management & Signal Chain | Superb Automation

LM139DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM139DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM139DR: four comparators on a 330 millimetre reel, and the coldest rail it will see

LM139DR is the military temperature grade of the quad differential comparator that the industry has used since the nineteen seventies, in the fourteen pin SOIC body and on a 2500 piece reel. Four independent comparators share one supply pin and one ground pin, and each has its own input pair and its own open collector output. The grade is the point of the code: minus 55 to plus 125 degrees, wider than the LM239 at minus 25 to plus 85 and much wider than the LM339 at zero to plus 70.

A buyer usually arrives here after a cheaper grade has drifted out of window on a cold morning. The difference is not a different die. It is the same comparator with a wider guaranteed window and a full range test at both ends of it, which is why the offset maximum moves from 5 to 9 millivolts and why the reel price moves with it.

This page covers what the vendor document prints for the code, the rows that change with temperature, the carrier, and where four comparators in one body earn their place against four singles or one dual plus two singles.

LM139DR as the vendor document publishes it

The rows below come from the current vendor document, revision Z dated May 2025, at a 5 volt supply unless the row says otherwise. Values are maximum unless the row is marked typical.

Channels4, independent, one supply pin pair
Supply voltage2 to 36 volts, split rails to plus or minus 18 volts
Input offset voltage2 millivolts typical, 5 maximum at 25 degrees
Input offset voltage over temperature9 millivolts maximum, minus 55 to plus 125 degrees
Input offset current3 nanoamps typical, 25 maximum
Input offset current over temperature100 nanoamps maximum
Input bias current25 nanoamps typical, 100 maximum
Input bias current over temperature300 nanoamps maximum
Common mode range0 to supply minus 1.5 volts at 25 degrees
Common mode range over temperature0 to supply minus 2 volts
Differential input voltageplus or minus 36 volts, both inputs
Large signal gain200 volts per millivolt typical
Output low voltage150 millivolts typical, 400 maximum at 4 milliamps
Output low voltage over temperature700 millivolts maximum
Output sink current6 milliamps minimum at 1.5 volts of saturation
Output leakage0.1 nanoamps at 5 volts, 1 microamp at 30 volts over temperature
Supply current, four comparators0.8 milliamps typical, 2 maximum, output high, no load
Response time1.3 microseconds, 100 millivolt step with 5 millivolts of overdrive
Response time, logic step0.3 microseconds, full logic swing
Outputopen collector, rated to 36 volts
Operating temperatureminus 55 to plus 125 degrees
Package14 pins, SOIC body D
Carrier2500 pieces on a 330 millimetre reel

Two millivolts typical, five maximum at room, nine across the military window

The input offset voltage of LM139DR is 2 millivolts typical and 5 millivolts maximum at 25 degrees, and the same parameter is guaranteed at 9 millivolts over the full minus 55 to plus 125 window. The A grade of the family prints 2 millivolts maximum at room and 4 millivolts over temperature, so a threshold that has to hold to a couple of millivolts on a cold morning should be the A code rather than this one.

On a 5 volt rail, 9 millivolts is 0.18 per cent of full scale. On a divider watching a 12 volt battery it becomes a few tens of millivolts at the battery, which is acceptable for a low battery flag and not acceptable for a cell balancing decision. The offset is a fixed error per part, so a single point calibration at room temperature removes most of it and leaves the drift, which is small on this die.

The input bias current matters more than the offset in a high impedance sense. At 300 nanoamps over temperature, a 100 kilo ohm divider carries 30 millivolts of error, and a 1 megaohm divider carries 300 millivolts, which is usually the point where a buffer or a lower divider value is the better fix than a tighter comparator.

An input range that reaches the negative rail, and one and a half volts lost at the top

The common mode range includes ground, from zero to the supply minus 1.5 volts at 25 degrees and to the supply minus 2 volts over temperature. That is what makes the part usable on a single supply with a low side shunt: the input sits tens of millivolts above ground and the comparator still resolves it. Either input can also be taken to 36 volts, or 0.3 volts below ground, without damage, which is why the part survives a divider that is still settling when the rail comes up.

The 1.5 volts lost at the top is the row that catches people. A comparator that watches a 5 volt rail with a 4.9 volt threshold is inside the window at room temperature and outside it at 125 degrees, where the window closes at 3 volts. Either divide the sense down or move that threshold to a part with a rail to rail input. On a 15 volt rail the same loss is 10 per cent and rarely matters.

The differential limit is plus or minus 36 volts, which is the same as the supply limit rather than a separate protection clamp, so a reversed divider or a hot plug event on an input does not need an external diode in most industrial boards. That single row removes two parts from the bill of materials on a 24 volt board.

One and three tenths of a microsecond, and three hundred nanoseconds on a logic step

Response time is 1.3 microseconds with a 100 millivolt step and 5 millivolts of overdrive, and 0.3 microseconds when the step is a full logic swing. The test condition is a 5.1 kilo ohm pull up to 5 volts with 15 picofarads of load, so a slower edge or a heavier load lengthens both figures. A 10 kilo ohm pull up roughly doubles the small signal figure.

The output sinks 6 milliamps minimum and 16 milliamps typical at 1.5 volts of saturation, and leaks 0.1 nanoamps at 5 volts with 1 microamp over temperature at 30 volts. That sink drives an optocoupler directly, or a small relay through a transistor, and the 36 volt output rating lets the same part pull a 24 volt PLC input without a level shift.

Saturation is 150 millivolts typical and 400 millivolts maximum at 4 milliamps, rising to 700 millivolts over temperature. An engineer who counts on the typical number and needs a clean logic low at 0.4 volts has no margin at 125 degrees, so size the pull up and the load against the 700 millivolt row.

What four comparators cost on a standby rail

The supply current for all four comparators is 0.8 milliamps typical and 2 milliamps maximum at 5 volts, with no load and the output high. It is quoted for the package rather than per comparator, and it barely moves with supply voltage, which is unusual and useful on a 24 volt board because the current does not grow with the rail.

On an instrument that sleeps, 2 milliamps is the largest single term in the standby budget and is the usual reason an engineer moves to the B version of the family, which the vendor rates at 200 microamps per comparator. The B part is a drop in replacement in the same fourteen pin body, so the change is a part number rather than a board change, and the offset improves at the same time.

The carrier: 2500 pieces on a 330 millimetre reel

LM139DR is the tape and reel code. The vendor tape and reel table prints 2500 pieces on a 330 millimetre reel, a 16.4 millimetre tape width, a 6.5 millimetre pocket and 2.1 millimetres of depth. The same body is offered in a tube carrier, which is the right choice for a pilot build and the wrong one for a line that runs more than a few hundred boards a week.

LM139DRSOIC D, 14 pins2500 pieces, 330 millimetre reelthe standard production carrier
LM139DRG4SOIC D, 14 pins2500 pieces, 330 millimetre reelgreen mould compound code of the same body
LM139ADSOIC D, 14 pinstubeA grade, 2 millivolts maximum at room
LM139ADRSOIC D, 14 pins2500 pieces, 330 millimetre reelA grade on the reel

The tube carrier is worth keeping on the approved vendor list even when the line runs reels, because a service centre that repairs twenty boards does not want to open a 2500 piece reel for two parts.

Where the quad military comparator belongs

Four comparators in one body belong where the thresholds are related: a four cell battery stack with one window per cell, a four channel alarm board, a quad window on a single rail, or a level translator bank. Four comparators on one die also means one temperature coefficient and one offset distribution, so a four point calibration is one table rather than four.

It is the wrong answer when the four thresholds live in different voltage domains, because the common mode range is shared. One comparator watching a 200 volt rail and another watching a 0.5 volt shunt in the same package works only if both dividers land inside zero to supply minus 1.5 volts, and that is usually the point where two dual parts become the cheaper route.

On the sourcing side the LM139 family has been second sourced for decades, which makes it one of the easier cross references in a power management bill of materials. Our power management cross reference page lists the codes that share this pinout, and the last time buy planning page covers what to do when a particular suffix stops appearing in the addendum.

Buying questions that come with this code

Is LM139DR the same die as LM239DR? Yes. The two codes share the comparator and the fourteen pin body, and the difference is the guaranteed temperature window and the full range test that comes with it.

Does the R suffix change the part? No. D is the SOIC body and R is the reel carrier, so the electrical rows are identical to the tube code.

What should be checked on receipt? Date code, reel quantity and moisture level. The part is printed at level 1 with unlimited floor life, so an old reel is usable, but the reel label is the only place the date code is printed and it is the first thing an incoming inspection plan should record.