ISO7731DBQR
Product Specifications
ISO7731DBQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7731DBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7731DBQR: triple-channel reinforced digital isolator at 100 Mbps in a 16-pin QSOP
ISO7731DBQR is three reinforced isolation channels at 100 Mbps, two forward and one reverse in a QSOP body of 16 pins. The 7731 channel mix is two forward and one reverse, which covers a clock and a data line out with a single return. The DBQ body is the QSOP option rated 3000 V RMS, useful where the board area is fixed and the barrier does not have to be the widest one on the panel.
Order code and package
| Order code | ISO7731DBQR |
| Function | triple-channel reinforced digital isolator |
| Package | QSOP, 16 pins, DBQ body |
| Channels | three, two forward and one reverse |
| Data rate | 100 Mbps |
| Supply range | 2.25 V to 5.5 V on each side |
| Isolation | 3000 V RMS in this body, 5000 V RMS in the wide SOIC |
| Transient immunity | 100 kV per microsecond typical |
| Barrier life | over 30 years at 1500 V RMS working voltage |
| Default output | high on the plain code, low on the F version |
| Temperature range | minus 40 to plus 125 C |
| Channels available in family | two, three and four |
Electrical parameters that decide the application
| Barrier | silicon dioxide, reinforced |
| Surge capability | up to 12.8 kV |
| Esd | 8 kV IEC 61000-4-2 contact discharge across the barrier |
| Level translation | 2.25 V to 5.5 V on each side |
| Certifications | VDE 0884-17, UL 1577, IEC 61010-1, IEC 62368-1, IEC 60601-1, GB 4943.1 |
| Output | CMOS push pull on every channel |
| Channel direction | two forward, one reverse, fixed |
| Body options | wide SOIC and this QSOP |
Points to check before this part goes on a BOM
Two forward and one reverse is the right mix for a serial interface with a single return line, and it is the reason a triple exists between the dual and the quad. A quad ordered for three signals leaves one channel carrying nothing and drawing current on both sides.
The QSOP body is rated 3000 V RMS against 5000 V RMS for the wide SOIC version of the same die. Both are reinforced parts, and the difference is the package creepage, so the choice follows the safety file rather than the data rate.
The 100 Mbps rate is the same across the family and does not change with channel count. What changes is the quiescent current, because each channel draws on both sides whether or not it is switching, which is the hidden cost of ordering the quad for a triple interface.
The default output state appears before the controller drives anything, so a channel that enables a power stage should be assigned to the version whose default is the safe state. On this family that is the F code for a default low, and the plain code for a default high.
Where this order code fits
Isolated sensor interfaces, digital IO modules and instrument front ends order this code when three signals have to cross one barrier in a small body. Boards comparing it with a neighbouring part start from our Medical Device Components page, and boards replacing a part that has gone end of life start from the Vendor Consolidation page.
Questions buyers ask
Can the three channels be split across two different barriers? No. All three share one barrier against the opposite side; the direction of each channel is what differs.
Is the QSOP body suitable for a mains barrier? It is a reinforced part rated 3000 V RMS in this body, which covers many industrial rails; the wide SOIC version is the one with the 5000 V RMS rating.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.