ISO7710FQDRQ1
Product Specifications
ISO7710FQDRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7710FQDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7710FQDRQ1: single-channel reinforced digital isolator at 100 Mbps with default low output in an 8-pin SOIC
ISO7710FQDRQ1 is one reinforced isolation channel at 100 Mbps with a default low output on the automotive order code in a SOIC body of 8 pins. The F in this code sets the default output low, the Q1 suffix makes it the automotive qualified part, and the single channel sits in an 8-pin narrow SOIC rated 3000 V RMS. The family runs at 100 Mbps, from a 2.25 V to 5.5 V supply on each side, with 100 kV per microsecond typical transient immunity and a 30 year projected barrier life at 1500 V RMS working voltage.
Order code and package
| Order code | ISO7710FQDRQ1 |
| Function | single-channel reinforced digital isolator |
| Package | SOIC, 8 pins, D body |
| Channels | one |
| Data rate | 100 Mbps |
| Default output | low, set by the F suffix |
| Supply range | 2.25 V to 5.5 V on each side |
| Isolation | 3000 V RMS in the D body, 5000 V RMS in the DW body |
| Surge capability | up to 12.8 kV |
| Transient immunity | 100 kV per microsecond typical |
| Barrier life | over 30 years at 1500 V RMS working voltage |
| Temperature range | minus 40 to plus 125 C |
| Qualification | automotive Q1 order code |
Electrical parameters that decide the application
| Barrier | silicon dioxide, reinforced |
| Esd | 8 kV IEC 61000-4-2 contact discharge across the barrier |
| Level translation | 2.25 V to 5.5 V on each side, any combination |
| Emc | system level ESD, EFT and surge immunity, low emissions |
| Default options | high on the plain code, low on this F code |
| Certifications | VDE 0884-17 reinforced, UL 1577, IEC 62368-1, IEC 61010-1, IEC 60601-1, GB 4943.1 |
| Body options | wide SOIC DW-16 and narrow SOIC D-8 |
| Channel count | one in this body |
Points to check before this part goes on a BOM
The default output state is a safety decision, not a preference. With the input undriven, this code holds the output low, so a gate enable or a driver strobe that must be inactive during power up belongs on the F version rather than on a pull resistor that may be fitted on the wrong side of the barrier.
The 8-pin narrow body is rated 3000 V RMS while the wide body of the same die is rated 5000 V RMS. On an automotive 400 V bus, the narrow body provides the functional and basic isolation the pack monitor needs, and the wide body is the one that carries a reinforced rating for a mains connected charger.
One hundred kilovolts per microsecond of typical transient immunity is what allows this part to sit across the barrier from a switching node without the output glitching. The common mode step at a fast edge is the condition that breaks weaker isolators, and the data sheet states the immunity at a defined common mode voltage rather than as a headline.
A single channel in an 8-pin body frees the pins for wider spacing. Where a board needs one signal and a lot of creepage, this is the package that gives both, and the dual and quad parts of the family would put two or four channels on the same barrier for the same footprint.
Where this order code fits
Isolated enable and fault lines in automotive power stages, and single signal barriers on charger and battery management boards, order this code where one channel is all the interface needs. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What does the F suffix change? Only the default output state. The F code drives low with the input undriven; the plain code drives high. Rate and isolation stay the same.
Is the Q1 code a different die? No. The 100 Mbps rate, the 30 year life and the 12.8 kV surge figure belong to the family; the Q1 suffix adds the automotive qualification and the order code.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.