ISO7421EDR
Product Specifications
ISO7421EDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7421EDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7421EDR: the fast low power dual on a large reel, default output high
ISO7421EDR is the E code of the dual channel digital isolator in the narrow body eight pin SOIC on a large reel of 2500, one channel in each direction, default output high, signaling rate above 50 megabits per second with a propagation delay of 7 nanoseconds typical. The pulse skew is about 200 picoseconds.
The supply current is the reason this part exists beside the wider family: 1.8 milliamps per channel at 1 megabit and 2.8 milliamps per channel at 25 megabits on a 3.3 volt supply. With no integrated noise filter the delay stays short, which is what an encoder interface or a serial clock needs, and the price is that a spike on the input reaches the output.
ISO7421EDR as the vendor document publishes it
| Channels | 2, one in each direction |
| Signaling rate | above 50 megabits per second |
| Propagation delay | 7 nanoseconds typical |
| Pulse skew | 200 picoseconds typical |
| Channel to channel skew | 1 nanosecond maximum on the E grade |
| Common mode transient immunity | 25 kilovolts per microsecond minimum, 50 typical |
| Supply | 3 to 5.5 volts per side |
| Supply current at 1 megabit | 1.8 milliamps per channel at 3.3 volts |
| Supply current at 25 megabits | 2.8 milliamps per channel at 3.3 volts |
| Input thresholds | transistor transistor logic, 5 volt tolerant inputs at 3.3 volts |
| Withstand isolation | 2500 volts root mean square for 60 seconds |
| Maximum working isolation | 566 volts peak |
| Maximum transient isolation | 4242 volts peak |
| Clearance and creepage | 4 millimetres |
| Barrier life | above 25 years at the rated working voltage |
| Temperature range | minus 40 to plus 125 degrees |
| Package | 8 pins, narrow body SOIC D |
| Catalogue code | ISO7421EDR |
| Vendor status | active |
| Default output | high, plain code without the F suffix |
| Carrier | large reel of 2500 |
| Moisture level | level 1, 260 degrees, unlimited floor life |
Fifty megabits and seven nanoseconds
ISO7421EDR is the dual channel member of the ISO742x family, with the two channels in opposite directions, in an eight pin narrow body SOIC. The family is published as a fast part: the signaling rate is above 50 megabits per second, the propagation delay is 7 nanoseconds typical, and the pulse skew is about 200 picoseconds.
There is no integrated noise filter on the channel, which is why the delay is that short: a filter would add tens of nanoseconds and would also limit the rate. The trade is that a narrow spike on the input reaches the output, so the driving logic has to be clean rather than the isolator cleaning it up.
Default high, default low, and the letter that decides
The default output state of ISO7421EDR is set by the suffix: the plain code drives the output high when the input side loses power, and the F code drives it low. That is the opposite convention to some other families in the catalogue, so the letter has to be checked against the order code rather than assumed from a neighbouring part.
On a full duplex link the default decides what the receiver sees during a power sequencing event. A high default on a receive line looks like an idle bus, which is usually harmless; a high default on an enable line can turn a driver on, which is not. That is the case where the F code is worth waiting for.
One and eight tenths milliamps per channel at 3.3 volts
The supply current of ISO7421EDR at 3.3 volts is 1.8 milliamps per channel at 1 megabit per second and 2.8 milliamps per channel at 25 megabits per second, which is the lowest of the isolators in this catalogue at the higher rate. Both sides draw the same current on a symmetric link.
That current is dominated by the switching of the barrier rather than by the logic, which is why it rises by only 1 milliamp between 1 and 25 megabits: the edge rate is fixed and only the number of edges changes. A link that is idle draws the quiescent figure, and a link that runs a clock continuously draws the higher one regardless of the data on it.
Twenty five hundred volts, 4242 volts peak, four millimetres
The barrier of ISO7421EDR is rated 2500 volts root mean square of withstand for 60 seconds and 4242 volts peak of maximum transient isolation voltage, with 566 volts peak of maximum working isolation voltage. The clearance and creepage are 4 millimetres, the barrier capacitance is about 1 picofarad, and the insulation life is quoted above 25 years.
The 25 year figure is a projection at a stated working voltage rather than a guarantee at any voltage, and it is the reason the working voltage row matters more than the type test. Four millimetres of creepage is the board rule, and the barrier capacitance matters on a link where the common mode step is fast, because 1 picofarad at 25 kilovolts per microsecond is 25 milliamps of displacement current.
TTL thresholds, 5 volt tolerant inputs, and translation
ISO7421EDR has transistor transistor logic input thresholds, so a 3.3 volt logic output drives it directly without a divider, and the inputs are 5 volt tolerant when the part runs at 3.3 volts. The supply window is 3 to 5.5 volts on each side, which allows the two sides to run at different levels and makes the part a level translator as well as a barrier.
That combination is why the family is used between a 1.8 or 3.3 volt controller and a 5 volt interface without a separate translator. The output drive is 4 milliamps at 0.4 volts of low level, which is enough for one complementary metal oxide semiconductor load and not enough for a bus, so the isolator sits behind a transceiver rather than on the bus itself.
Where a fast dual isolator belongs
ISO7421EDR belongs on an isolated serial peripheral interface clock and data pair at 20 megahertz, on an isolated gate drive signal where the delay has to be a few nanoseconds, on an encoder interface where the edge timing is the measurement, and on a digital isolator position in front of a controller area network or RS-485 transceiver.
The two rows that decide those cases are the 7 nanosecond typical delay and the 2500 volt barrier, and the 4 millimetre creepage is the constraint on the board. Where the creepage has to be 8 millimetres, this part cannot be used however fast it is, and the wide body quad in the same catalogue is the alternative.
What a fast isolator does to the driver
A 7 nanosecond propagation delay means the isolator is not the slowest element in the link, so the driver and the receiver become the timing budget. A logic gate with 5 nanoseconds of rise time and a 3 nanosecond skew is already comparable with the isolator, and the sum, not the isolator alone, is what the setup and hold calculation uses.
The second consequence is that the part does not filter. A 2 nanosecond glitch on the input appears on the output with the same width, so a link that used an optocoupler for its slow response needs a filter in front of this part rather than after it. That is the one row of the family table that no electrical figure shows.
A 7 nanosecond delay with 2 milliamps per channel is the combination to check against the link. Our BOM scrubbing page covers the isolator against the bill of materials, and the vendor consolidation page covers the family against the wider parts.
What does the E suffix mean? The E code is the plain default, which drives the output high when the input side loses power. The FE code drives it low, and the letter is the only difference.
Is 4 millimetres of creepage enough? It is enough for a functional or basic barrier at low working voltage. Where the product standard asks for 8 millimetres, this body cannot be used and the wide body quad is the alternative.