Contact Us

ISO7221ADR

Brand: Texas Instruments
Texas Instruments ISO7221ADR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7221ADR — Power Management & Signal Chain | Superb Automation

ISO7221ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7221ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7221ADR: dual-channel digital isolator at 1 Mbps with one channel each way in an 8-pin SOIC

ISO7221ADR is a two-channel digital isolator with one forward and one reverse channel at 1 Mbps in a SOIC body of 8 pins. This is the bidirectional arrangement of the ISO722x pair and the A grade, the 1 Mbps member of the four rate options. It is the code that replaces an optocoupler where the signals are slow, an enable line and a status line, and the price of the slow grade is paid back in supply current.

Order code and package

Order codeISO7221ADR
Functiondual-channel digital isolator, bidirectional
PackageSOIC, 8 pins, D body
Channelstwo, one forward and one reverse
Signaling rate1 Mbps, the A grade
Transient immunity50 kV per microsecond typical
Supply3.3 V or 5 V, with a 2.8 V C grade option on the same die
ESD4 kV
Isolation2500 V RMS per UL 1577
Temperature rangeminus 40 to plus 125 C
Pin outshared with the 7220 arrangement

Electrical parameters that decide the application

Barriersilicon dioxide
Pulse width distortionspecified in the switching table, tighter than the 1 Mbps link needs
OutputCMOS push pull
Grade options1, 5, 25 and 150 Mbps across A, B, C and M suffixes
Direction options7221 one each way, 7220 both forward
CertificationsVDE 0884-17 conformity, UL 1577, IEC 61010-1, IEC 62368-1
Supply currentlowest of the four grades at a given rate
Channel counttwo in this body

Points to check before this part goes on a BOM

One megabit per second is 1 microsecond per bit, and the propagation delay of this grade is specified well inside that. The number that matters on a UART is not the delay but the pulse width distortion, because a distorted pulse changes the duty cycle the receiver sees and shows up as a framing error at the far end.

The reverse channel makes this the code for a request and reply link. A board wired with the 7220 in this position has both channels pointing the same way and the reply never arrives, which is a failure that looks like a protocol problem rather than a part number problem.

The A grade is the slowest and lowest current member of the family. Where a 25 Mbps grade would also work, the A grade saves supply current on every channel, and on a module with eight isolated links that difference shows up in the thermal budget of the enclosure.

The isolation rating of 2500 V RMS is the 8-pin D body rating. A board that needs a wider barrier has to move to the wide body parts, because adding slots around an 8-pin package is not the same as a certified creepage distance.

Where this order code fits

Isolated UART ports, relay and enable interfaces and slow status links order this code because the data rate is fixed by the protocol and the isolation is what the board needs. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Is 1 Mbps enough for RS-485? Yes for the slow industrial rates and for opto-replacement duty. A 20 Mbps bus needs the M grade or a dedicated isolated transceiver.

Does it work with a 5 V signal on one side and 3.3 V on the other? Yes, each side runs from its own supply and the part translates levels in both directions.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.