Contact Us

ISO5851QDWRQ1

Brand: Texas Instruments
Texas Instruments ISO5851QDWRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO5851QDWRQ1 — Power Management & Signal Chain | Superb Automation

ISO5851QDWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO5851QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO5851QDWRQ1: isolated IGBT and MOSFET gate driver with 2.5 A source and 5 A sink in a 16-pin SOIC

ISO5851QDWRQ1 is a galvanically isolated gate driver with desaturation detection and active Miller clamping in a SOIC body of 16 pins. The output stage sources 2.5 amps and sinks 5 amps, enough to switch a 1200 V IGBT module without an external buffer, and the 100 kV per microsecond minimum transient immunity is what keeps the driver stable when the emitter of the switch it is driving moves 1500 volts in a few tens of nanoseconds. The Q1 order code is the automotive qualified member of the family.

Order code and package

Order codeISO5851QDWRQ1
Functionisolated gate driver with protection
PackageSOIC, 16 pins, DW body
Output current2.5 A peak source, 5 A peak sink
Common mode transient immunity100 kV per microsecond minimum at 1500 V common mode
Propagation delay76 nanoseconds typical, 110 nanoseconds maximum
Miller clamp2 A active clamp on the gate
Fault reportingdesaturation detection signalled on FLT, reset through RST
Undervoltage lockoutboth sides, with a RDY pin indication
Input supply3 V to 5.5 V
Output supply15 V to 30 V
Isolation8000 V peak transient, 2121 V peak working, reinforced
UL rating5700 V RMS for one minute
Temperature rangeminus 40 to plus 125 C ambient
Qualificationautomotive Q1 order code

Electrical parameters that decide the application

Barriersilicon dioxide, reinforced
Noise rejectioninput pulses shorter than 20 nanoseconds are rejected
Default stateoutput pulled low with a low supply or a floating input
Short circuitoutput short circuit clamp
UVLO on output sidekeeps the switch off until the driver supply is high enough for a full gate voltage
InputsCMOS compatible, 3 V to 5.5 V logic
CertificationsVDE V 0884-10, UL 1577, CSA notice 5A, TUV, CQC GB 4943.1
Package size10.30 mm by 10.30 mm body including pins

Points to check before this part goes on a BOM

Desaturation detection is the reason to pay for this part over a plain isolated driver. When the collector voltage of an IGBT fails to fall within the blanking time after turn on, the part reports the fault on FLT and turns the switch off through the same gate resistor, which is the difference between a short circuit that destroys a module and one that trips an alarm.

A 2 amp active Miller clamp holds the gate low when the opposite switch in the bridge turns on. Without it, the current through the gate collector capacitance can lift the gate enough to turn the switch partly on, and the resulting shoot through current is the failure that most often takes out a parallel pair.

The 100 kV per microsecond immunity is specified at 1500 V common mode, which is the condition a 1200 V module creates at every switching edge. A driver rated 25 kV per microsecond can be perfectly adequate on a 600 V stage and unreliable on this one, so the number has to be compared at the same common mode voltage.

Both supplies are monitored. The input side lockout stops the part from acting on a controller that is still booting, and the output side lockout stops it from turning on a switch with a gate voltage too low to keep the device in saturation, which would dissipate the whole bus in the die.

Where this order code fits

Traction inverters, charger bridges and motor drives order this code because the fault reporting and the soft turn off are inside the part rather than built from discrete parts around it. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it need an external desaturation diode? Yes, the high voltage diode from the collector and the blanking capacitor are external, and their values set the blanking time.

Can it drive a silicon carbide module? The drive currents and the 30 V output rail suit many SiC gates, but the negative bias and the gate resistor have to be worked out for the device rather than copied from an IGBT stage.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.