Contact Us

INA827AIDGKR

Brand: Texas Instruments
Texas Instruments INA827AIDGKR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA827AIDGKR — Power Management & Signal Chain | Superb Automation

INA827AIDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA827AIDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA827AIDGKR: the same fixed gain on a 2500 piece reel

INA827AIDGKR is the reel carrier of the fixed gain of 5 amplifier, 2500 pieces on a large reel in the 8 pin VSSOP. The electrical rows are the tube code's: 0.005 per cent typical of gain error at 5 with 1 ppm per degree of drift, 150 microvolts maximum of offset, 88 dB of rejection at that gain and 600 kHz of bandwidth.

Two rows make this part easy to specify and easy to get wrong. The gain is 5 only while the gain pins are open, and any resistor added to raise the gain puts the external tolerance back into the channel. The input range goes below the negative supply and stops a volt under the positive one, which is what a ground referenced bridge wants and what a high side shunt on a 24 volt bus does not.

INA827AIDGKR as the vendor document publishes it

Gain at the fixed setting5 V/V, trimmed inside the package, no external resistor
Gain equation above 55 plus 80 kilo-ohms divided by the external resistor, up to 1000
Gain error at 50.005 per cent typical, 0.035 per cent maximum
Gain drift at 51 ppm per degree maximum
Offset voltage150 microvolts maximum
Offset drift2.5 microvolts per degree maximum
Common mode rejection at a gain of 588 dB minimum, held to 5 kHz
Power supply rejection at a gain of 5100 dB minimum
Input bias current35 nanoamps typical, 50 nanoamps maximum
Voltage noise at a gain of 100017 nanovolts per root hertz
Bandwidth at a gain of 5600 kHz
Bandwidth at a gain of 100150 kHz
Input protection40 volts beyond the supply rails
Common mode rangebelow the negative supply to 1 volt below the positive supply
Supply current200 microamps typical
Supply range3 to 36 volts single, plus or minus 1.5 to plus or minus 18 volts dual
Outputrail to rail
Temperature rangeminus 40 to plus 125 degrees
BodyVSSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Vendor statusactive, 2500 piece large reel
Catalogue codeINA827AIDGKR
Vendor stringINA827AIDGKR
Lead finishNIPDAU
Moisture levellevel 2, 260 degrees, one year floor life

Three volts to thirty six, and the tube carrier

INA827AIDGKR runs from a single 3 to 36 volt supply or a dual plus or minus 1.5 to plus or minus 18 volt supply and is specified from minus 40 to plus 125 degrees. The 8 pin VSSOP body is 3 by 3 millimetres, which is the smallest body the family offers.

Two carriers exist and the difference is not cosmetic. The tube of 80 pieces suits a first build and a repair bench, and the 2500 piece reel suits a line. The moisture level is 2 with a one year floor life on both, and the lead finish differs between the two rows in the addendum, which is the column to read when a customer asks whether the part is tin or a nickel palladium gold finish.

A gain of five with no external resistor

INA827AIDGKR is trimmed to a fixed gain of 5 in the package, and at that gain there is no external resistor and therefore no external gain error: 0.005 per cent typical and 0.035 maximum of gain error, with 1 ppm per degree of gain drift. A single external resistor extends the gain from 5 to 1000, and the drift above 5 becomes the drift of that resistor.

That is a narrow but valuable position. Most instrumentation amplifiers need a resistor pair for any gain at all, and the pair is usually the largest error term on the board. Here the most common gain in industrial instrumentation, 5, is free of that term, and the channel that needs 100 pays for a resistor only because it asked for one. A board that runs several channels at exactly 5 therefore has one less component and one less tolerance to stack.

Six hundred kilohertz at five, a hundred and fifty at a hundred

The bandwidth of INA827AIDGKR is 600 kHz at a gain of 5 and 150 kHz at a gain of 100, with a noise of 17 nanovolts per root hertz at a gain of 1000 and 200 microamps of supply current. The output is rail to rail, so the swing is set by the converter rather than by the amplifier.

For a channel at a gain of 5 the 600 kHz figure is enough to drive a sampling converter directly at a few hundred kilo-samples per second, and the 150 kHz at a gain of 100 is enough for a multiplexed module at 10 kilo-samples. The capacitive load is not specified as generously as on the difference amplifier, so a long cable or a large sampling capacitor wants a series resistor, and that resistor costs a pole at the frequencies this part is bought for.

A hundred and fifty microvolts and two and a half microvolts per degree

The offset of INA827AIDGKR is 150 microvolts maximum with a drift of 2.5 microvolts per degree maximum, which is a wider window than the low noise members of the family and a tighter drift than most parts in its price class. Over 165 degrees the drift is 412 microvolts, which is nearly three times the room temperature maximum.

That arithmetic decides the applications. A channel that calibrates at 25 degrees and runs to 85 degrees sees 150 microvolts of drift, which on a 20 millivolt full scale bridge is three quarters of a per cent. A channel that runs at a constant temperature, or one that measures a large signal, never sees the row. Where the drift matters, the next part up the family has 0.4 microvolts per degree, and the price difference buys the drift rather than the offset.

Where a fixed gain of five earns its place

INA827AIDGKR belongs on an analogue input module with a fixed 5 V/V front end, a battery test channel, an LCD test fixture, an ECG front end that needs a fixed gain ahead of a converter, and any board that wants the gain accuracy of a trimmed network without the resistor pair.

It stops where the gain has to be other than 5 and the accuracy still matters, because above 5 the resistor sets the error. It stops where the offset has to be under 150 microvolts, and where the drift has to hold a 0.1 per cent channel over 60 degrees. And it stops where the common mode is far above the supply, because the input range goes below the negative rail rather than above the positive one. Our amplifier cross reference page covers the gain range of the family, and the BOM scrubbing page covers the carrier rows against the bill of materials.

Eighty eight decibels at a gain of five, held to five kilohertz

The common mode rejection of INA827AIDGKR is 88 dB minimum at a gain of 5 and holds to 5 kHz at the same gain, with 100 dB minimum of power supply rejection. The input range reaches below the negative supply, which is what a ground referenced bridge or a low side shunt needs.

The 88 dB figure turns a 10 volt common mode into 400 microvolts at the input, which is larger than the 150 microvolt offset, so a channel with a high common mode is limited by rejection rather than by the offset. That is the honest reading of a low cost part, and it is also why the part is specified at a gain of 5: at that gain the rejection is the best the architecture can do, and running it at 100 does not improve the row the way the three op amp family does.

Two thousand five hundred pieces is a line quantity and the gain is fixed. Our BOM scrubbing page covers the gain pins against the bill of materials, and the vendor consolidation page covers buying the tube and the reel on one line.

Can the gain be raised above 5? Yes, with one external resistor as 5 plus 80 kilo-ohms divided by it, up to 1000, and the accuracy then follows the resistor.

Is this the same part as the tube code? Yes, one die and one body; the carrier and the printed lead finish differ.