Contact Us

INA260AIPW

Brand: Texas Instruments
Texas Instruments INA260AIPW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA260AIPW — Power Management & Signal Chain | Superb Automation

INA260AIPW

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA260AIPW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA260AIPW: 15 A current and power monitor with an integrated 2 milliohm shunt

INA260AIPW is a digital current and power monitor with the shunt inside the package in a TSSOP body of 16 pins. The shunt is part of the part: a 2 milliohm resistor with a tolerance equivalent to 0.1 percent and a 10 ppm per C coefficient, rated for 15 amps continuous from minus 40 to plus 85 C. That removes the shunt choice, the Kelvin connection and one tolerance term from the BOM, and leaves an I2C part that reports current, voltage and power on buses from 0 V to 36 V.

Order code and package

Order codeINA260AIPW
Functioncurrent, voltage and power monitor with integrated shunt
Shunt2 milliohms, tolerance equivalent to 0.1 percent
Current rating15 amps continuous from minus 40 to plus 85 C
PackageTSSOP, 16 pins
Bus voltage range0 V to 36 V
Sensinghigh side or low side
InterfaceI2C, 16 programmable addresses
Supply2.7 V to 5.5 V
Temperature rangeminus 40 to plus 125 C
Shunt coefficient10 ppm per C from 0 to 125 C
DatasheetSBOS656 revision B

Electrical parameters that decide the application

System gain error0.15 percent maximum
Offset5 milliamps maximum, referred to current
Current resolution1.25 milliamps per least significant bit
Voltage resolution1.25 millivolts per least significant bit on the bus channel
Powercomputed in the part from the current and voltage registers
Averagingconfigurable, from one sample to 1024
Conversion timeprogrammable, with averaging the dominant term
Shunt dissipation225 milliwatts at the 15 amp rating
Shunt tolerance0.1 percent equivalent, fixed by the part vendor
Package optionsTSSOP 16 only on this part

Points to check before this part goes on a BOM

The 5 milliamp offset is a fixed floor and it dominates small loads. On a 100 milliamp standby current the offset alone is 5 percent of the reading, so this part is a 15 amp monitor and not a wide range one.

Fifteen amps through 2 milliohms is 225 milliwatts inside the package. The rating holds to 85 C ambient, and above that it derates; a board that runs the part near its limit needs copper under the body and a check of the junction temperature, not an assumption from the headline number.

The shunt is inside, so the current path has to be routed through the package. Two pins carry the load current and they are not the same pins that carry the sense signal, which is what keeps the Kelvin connection intact without the buyer making one.

0.15 percent system gain error is quoted for the whole chain, shunt included. That is the figure to compare against an amplifier plus a discrete 1 percent shunt, which is where the integrated part wins even though the amplifier alone looks tighter.

Sixteen addresses let several rails report on one bus. The address is strapped at build time, so the strap has to be decided when the board is signed off, not when the firmware team asks for another rail.

Averaging trades latency for resolution, and the trade is not linear. A protection loop that needs a trip inside a few hundred microseconds cannot use the long averaging settings, and the resolution it loses is the resolution it was counting on.

Where this order code fits

Rack power shelves, hot swap cards and battery testers are the boards that use it, because the current range is fixed and nobody has to argue about a shunt. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can the shunt be bypassed for a larger current? No. The 2 milliohm shunt is the current path through the package, so the 15 amp figure is a hard limit of this order code; a larger current needs an external shunt part.

Is the 0.1 percent shunt tolerance a calibration or a specification? It is a specification of the integrated resistor, and the 0.15 percent system gain error already includes it, so no separate shunt term is added to the error budget.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.