Contact Us

INA241A3IDDFR

Brand: Texas Instruments
Texas Instruments INA241A3IDDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA241A3IDDFR — Power Management & Signal Chain | Superb Automation

INA241A3IDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA241A3IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA241A3IDDFR: 110 V bidirectional current sense amplifier at 50 V per volt with enhanced PWM rejection

INA241A3IDDFR is a bidirectional current sense amplifier built for switching nodes, with rejection circuitry aimed at the common mode steps a motor drive or a converter puts on the shunt in a SOT-23-THIN body of 8 pins. It runs from a 2.7 V to 20 V supply, draws 2.5 mA, and measures current in both directions on a common mode from minus 5 V to 110 V, surviving 120 V. The A grade holds a 10 uV offset limit with 0.1 uV per degree of drift, and the gain is 50 V per volt on this member of the five gain family.

Order code and package

INA241A3IDDFRSOT-23-THIN DDF body, 8 pins, 3000 pieces on a large reel, Active, RoHS Yes, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 125 degrees
Part marking notethe addendum dated 8 November 2025 prints two marking strings across the A and .B rows of this string, 2PJ3 and 2U8B, so the marking on the reel label should be confirmed rather than assumed from the catalogue title
INA241B3IDDFRthe B grade at the same 50 V per volt gain, with a 150 uV offset limit and 0.5 uV per degree of drift instead of 10 uV and 0.1
INA241A3IDGKRVSSOP DGK body, 8 pins, 2500 pieces on a large reel at moisture level 2 with a one year floor life, marking I241A3
Other gainsA1 to A5 and B1 to B5 cover 10, 20, 50, 100 and 200 V per volt in the same three bodies

Electrical parameters that decide the application

Common mode rangeminus 5 V to 110 V in operation, minus 20 V to 120 V survival, independent of the supply
Bidirectionalthe output swings around the reference in both directions, so a charge and discharge current through one shunt is reported without a second device
Gain50 V per volt on this member, with 10, 20, 100 and 200 V per volt in the same family
Gain error0.01 per cent maximum with 1 ppm per degree of drift on the A grade, 0.1 per cent and 5 ppm per degree on the B grade
Offset voltage10 uV maximum with 0.1 uV per degree of drift on the A grade, 150 uV and 0.5 uV per degree on the B grade
Common mode rejection166 dB at DC, 104 dB at 100 kHz and 89 dB at 1 MHz, which is the reason the part exists
PWM rejectionthe internal circuitry suppresses the output disturbance from common mode steps at switching frequencies up to 125 kHz
Bandwidth1.1 MHz at every gain, rather than falling with gain like a voltage feedback instrumentation amplifier
Slew rate and settling8 V per microsecond, 1 us to 1 per cent on a step, which is fast enough to follow a current step inside one switching period
Supply and current2.7 V to 20 V, 2.5 mA of quiescent current, specified from minus 40 to plus 125 degrees
Referencean external reference sets the zero current output level, so a bidirectional measurement on a single supply can sit at mid rail

Family variants and how they differ

A against B gradethe letter is an accuracy grade here, unlike the INA293 where it is a pin-out variant: A gives 10 uV and 0.01 per cent, B gives 150 uV and 0.1 per cent, at the same gain and the same bandwidth
INA241 against INA293the INA241 adds bidirectional operation, the 10 uV offset limit and the PWM rejection, and draws 2.5 mA against 1.5 mA
INA240 as the earlier partthe INA240 carries the same enhanced rejection idea at 400 kHz of common mode suppression and a different offset grade, so a board moving from it should compare the rejection bandwidth rather than the headline offset
Gain selectionwith 50 V per volt a 1 milliohm shunt gives 50 mV per ampere, so a 20 A peak lands at 1 V and leaves headroom on a 3.3 V rail with a mid rail reference
Package and moisturethe DDF body is level 1 unlimited, the DGK body and the SOIC body are level 2 with a year, so the footprint choice changes the handling rule

Points to check before this part goes on a BOM

The rejection figures are quoted at frequency because that is where the part is used. 166 dB at DC is better than most instrumentation amplifiers, but the number that decides a motor drive is 104 dB at 100 kHz and 89 dB at 1 MHz, and the enhancement is aimed at switching edges up to 125 kHz. A drive running at 200 kHz is outside the range the enhancement was built for even though the DC figure still applies.

The 10 uV offset limit is the reason this part can use a small shunt. At 50 V per volt a 10 uV input offset is 500 uV at the output, which on a 3.3 V rail with a 1.65 V reference is 0.03 per cent of full scale, and the same error in amperes on a 1 milliohm shunt is 10 mA. That is the number to put against the resolution the host converter can read.

Bandwidth is flat at 1.1 MHz across all five gains, which is unusual and useful. A voltage feedback instrumentation amplifier loses bandwidth as gain rises, so a high gain member would be slow, while here the 200 V per volt member has the same 1.1 MHz as the 10 V per volt member. A fast over current comparator therefore does not have to sit on the lowest gain.

The B grade is not a reject. It carries 150 uV of offset and 0.1 per cent of gain error, which is still better than the 16 bit monitors on the same board, and it costs less. A board that only needs a fault threshold rather than a measurement should start from the B grade and move to A only if the threshold has to be tight.

The reference pin is what makes a bidirectional measurement possible on a single supply. With the reference at mid rail the output sits at half supply at zero current and swings either way, and any error in that reference appears directly at the output. A 0.1 per cent reference on a 3.3 V rail is 1.65 mV of zero current error, which at 50 V per volt is 33 uV referred to the input, three times the amplifier's own offset.

The moisture level difference between the bodies is worth a line on the process sheet. The DDF body is level 1 with unlimited floor life and the DGK and D bodies are level 2 with one year, so a line that keeps a partially used reel on the bench for a month is inside the limit on either body but the record keeping differs.

What PWM rejection does to a phase current waveform

A motor phase shunt sees a common mode that jumps between the rail and ground on every switching edge, and the amplifier has to ignore that jump while resolving a shunt drop of tens of millivolts. Without rejection the output shows a spike at each edge that the sampling converter can catch, and the current reading becomes dependent on where in the switching period the sample was taken. The INA241 suppresses that disturbance up to 125 kHz, which is the band where most drives run.

Reference error is part of the offset budget

The zero current level is set by an external reference and by the divider that feeds it. A 0.1 per cent reference and a 0.1 per cent divider are 0.2 per cent of the output range, which at 50 V per volt is a larger input referred error than the 10 uV offset, so a board that pays for the A grade and then uses a 1 per cent reference has bought the wrong half of the accuracy.

Where this order code fits

Motor drives, solenoids and actuators, injection molding machines, cordless power tools, medical cordless tools and drone propeller speed control are the applications the vendor names, and all of them present a shunt on a node that switches. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the A suffix a pin-out variant here? No. In the INA241 the letter is the accuracy grade: A is 10 uV and 0.01 per cent, B is 150 uV and 0.1 per cent.

Can it measure current in both directions? Yes. The output is bidirectional around the external reference, so charge and discharge current through one shunt are both reported.

What switching frequency does the rejection cover? Up to 125 kHz of common mode step, with 104 dB of rejection at 100 kHz.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.