VBFB1311
Product Specifications
VBFB1311
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBFB1311 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBFB1311: a 30 V, 50 A N channel in TO251
The VBFB1311 is a single N channel MOSFET in a TO251 body rated at 30 V, plus or minus 20 V on the gate, 50 A of drain current, with a threshold of 1.7 V. The catalogue gives 9 milliohm at 4.5 V and 7 milliohm at 10 V, on trench silicon.
TO251 is the body often called IPAK. It carries the same die as the equivalent TO252 but without the bent tab, so it stands upright on the board, takes less board area and puts the tab in the air where a clip or a small heatsink can reach it.
Thirty volts and 7 milliohm is a 12 V rail part. It is the class used for a motor drive on a 12 V battery, a load switch on a 5 V or 12 V rail, and the low side of a buck converter running from 12 V.
Key data for the VBFB1311
| Configuration | Single N channel |
| Package | TO251, IPAK, upright with exposed tab |
| VDS | 30 V |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V |
| ID | 50 A |
| RDS(on) at 4.5 V | 9 milliohm |
| RDS(on) at 10 V | 7 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, drop about 0.8 V at several amps |
| Thermal path | Tab in free air, plus the three leads |
| Gate charge | Not published on the catalogue page |
| Typical use | 12 V motor drive, load switch, buck low side |
TO251 against TO252
The die is the same and the electrical figures are the same. What changes is the thermal path. A TO252 lies flat with its tab soldered to a copper pad, so the whole tab area is a heat spreader into the board. A TO251 stands up, so only the three leads touch the board and the tab sheds heat to the air.
For a part dissipating under a watt the two are close. Above that the TO252 wins on a board with copper, and the TO251 wins only when there is air movement or a clip on the tab. A TO251 in a sealed enclosure with no airflow is the worst of both, because the tab has no copper and no air.
The other difference is height. A TO251 is taller than a TO252, which matters in a low profile product, and its leads are shorter, which slightly reduces the lead inductance. That is a small advantage in a fast switching cell, and it is not enough to justify the thermal penalty on its own.
Seven milliohms and fifty amps at 30 V
At 7 milliohm and 20 A the loss is 2.8 W. With the tab in free air and a junction to ambient near 60 degrees per watt, that is a 168 C rise, so 20 A is not continuous in a standing package. At 10 A the loss is 0.7 W and the rise 42 C, which works.
At 30 V the die is small for its current rating, which is why the resistance is low. The 50 A figure belongs to a die at 25 C and a tab held cold, and the standing body makes that harder to achieve than in a flat package.
The threshold of 1.7 V suits a 4.5 V drive. At 3.3 V the overdrive at the top of the threshold window is 1.6 V, which is usable but will not reach the published resistance, and at 1.8 V it is not usable at all.
The gate drive is where a 30 V part is easiest to get wrong. A threshold of 1.7 V and a 4.5 V column suggest a logic drive, and a 3.3 V microcontroller can indeed turn the part on. What it cannot do is turn it off quickly into a motor, because the same low threshold means the gate sits close to conduction when the driver releases it. A 10 k resistor from gate to source and a driver with an active pull down solve that. A bare pin with a series resistor does not, and the symptom is a switch that runs warm at low duty and cool at high duty, which is the signature of a gate that is being held partly on by the motor's own dV/dt.
In a 12 V motor drive the freewheel path is worth checking. When the low side switch turns off, the motor inductance drives current through the body diode of the high side device or through a separate diode, and at 10 A that is 8 W for the duration of the freewheel. At 20 kHz with a 50 per cent duty the diode conducts for a fraction of each period, and the average loss is small, but the peak junction temperature during a locked rotor is what limits the drive.
Where the part fits and where it does not
It fits a 12 V motor drive up to about 10 A, a load switch on a 12 V rail, a buck low side running from 12 V at a few hundred kilohertz, and any board where a standing package saves space. It does not fit a sealed enclosure with no airflow at high current, and it does not fit a 24 V rail without a voltage check.
Our safety stock planning page covers how a buffer is sized for a part that appears on several boards, which is the usual situation for a 30 V logic level switch.
The sourcing side of this part is covered on the material requirements planning. For a 30 V switch that sits on several boards, that page covers how demand is planned across builds.
Questions we get on this code
Can it be soldered to a copper pad? The tab can be soldered if the footprint allows it, and that changes the thermal behaviour completely. Most footprints for this body leave the tab in the air.
Is 30 V enough for a 24 V rail? No. A 24 V rail with any switching spike exceeds 30 V, and the part has no published avalanche margin.
Does the body diode need a separate part? No, but in a motor drive the diode carries the freewheel current, and its forward drop at several amps is 0.8 V, which is a real loss.
What should a purchase order carry? Part number, TO251 body, reel or tube, and date code. We confirm the packing on the quotation.