Contact Us

VBBC1309

Brand: VBsemi
VBsemi VBBC1309 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBBC1309 — Discrete & Power Semiconductors | Superb Automation

VBBC1309

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBBC1309 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBBC1309: a 30 V N channel at 13 A in a 3 by 3 DFN

The VBBC1309 is a single N channel MOSFET in a DFN body of 3 by 3 mm with a 30 V drain to source rating, a plus or minus 20 V gate window, a 1.7 V threshold, a 13 A current figure and resistances of 11 milliohm at 4.5 V and 8 milliohm at 10 V.

The body is the point of this part. A DFN 3 by 3 has an exposed pad on the underside, which is soldered to the board and carries heat straight into the copper. The same die in an SOP8 would run at 60 to 90 degrees per watt; in this body with a good pad it can be 30 to 40.

That is what makes 8 milliohm and 13 A a usable combination rather than a table entry. At 13 A and 8 milliohm the loss is 1.35 W, and at 40 degrees per watt that is a 54 C rise, which is a working number. The same loss in an SOP8 would be at the edge of what the body can pass.

Key data for the VBBC1309

ConfigurationSingle N channel
PackageDFN 3 by 3 mm, exposed pad, surface mount
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V
ID13 A
RDS(on) at 4.5 V11 milliohm
RDS(on) at 10 V8 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal pathExposed pad to board copper, the leads carry very little
VoidingPad voiding above about 20 per cent turns the thermal path into a hot spot
InspectionX-ray or a thermal image after the first build

Eight milliohms and where the heat goes

The exposed pad is the whole thermal story. A 3 by 3 mm pad soldered to 25 by 25 mm of two ounce copper gives a junction to ambient resistance near 40 degrees per watt with no airflow, and 30 with a little. At 1.35 W that is a 40 to 54 C rise, so a 60 C ambient lands the junction near 115 C, inside the usual 150 C limit with margin.

The same calculation with a poor solder joint is very different. A 30 per cent void under the pad removes a third of the heat path, and the junction to ambient resistance rises by roughly the same fraction. That is why the pad voiding figure matters more here than on a part whose heat leaves by the leads, and why a first build should be X-rayed or imaged under load.

The leads in a DFN carry very little heat. They are small and mostly serve to connect, so a board that relies on the lead copper rather than the pad is not using the body as intended.

Eleven against eight milliohms and the gate drive

The two columns differ by 27 per cent, which means a 5 V gate drive gets 11 milliohm and a 10 V drive gets 8. At 10 A that is a 300 mW difference, which on a 40 degree per watt path is a 12 C difference in junction temperature. Small, but it is free if a 10 V rail exists.

The 1.7 V threshold means the part is close to enhanced at 4.5 V and fully enhanced at 10 V, and the gate charge is the parameter that decides the switching loss. It is not published, so a converter at a few hundred kilohertz has to have the figure from the data sheet before the driver is chosen.

For a low frequency application, a load switch or a motor leg, the gate charge hardly matters and the 11 milliohm column at a 5 V gate is the useful number. That is the majority of the use cases for a 30 V 13 A part in this body.

The pad connection is also the electrical return, so a via array under it serves two purposes. Six to nine vias of 0.3 mm in a 3 by 3 pattern, connected to a ground or power plane, lower the thermal resistance and shorten the source inductance at the same time, which is what a synchronous buck wants. The vias have to be tented or plugged on the underside if the board is reflowed twice, and they have to be outside the area where the paste is printed so the paste is not drawn into them during reflow.

Where it fits

It fits a 12 V synchronous buck at 8 to 12 A, a load switch on a 12 V rail, a motor drive leg, and a battery protection switch where the heat has to leave through the board. It does not fit a 24 V rail, and it does not fit a board that cannot give the pad a solid copper landing.

Our incoming inspection plan page covers what is checked when a reel arrives, which for a DFN body includes the coplanarity of the pad and the moisture level on the label.

The sourcing side of this part is covered on the PCBA quote checklist. For a part whose heat leaves through the pad, that page covers what has to be settled before a quote is firm.

Questions we get on this code

Does it need a thermal via array under the pad? It helps. Vias into an inner copper plane lower the resistance beyond what the top copper alone gives.

Is 13 A continuous? With a good pad and airflow, yes. Without them the working figure is nearer 8 A.

Is 30 V enough for a 12 V rail? Yes with a wide margin, and the switch node ring stays inside the rating if the input capacitor is close.

What does the moisture label say? We report the level printed on the reel label rather than assuming a default.