VBA4625
Product Specifications
VBA4625
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA4625 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA4625: a minus 60 V dual P channel at minus 8.5 A
The VBA4625 is a dual P channel MOSFET in an SOP8 body with minus 60 V per device, a plus or minus 20 V gate window, a minus 1.7 V threshold, a drain current of minus 8.5 A and resistances of 30 milliohm at 4.5 V and 20 milliohm at 10 V, on trench silicon.
Sixty volts and 20 milliohm from a P channel in an SOP8 body is a serious die. The same resistance and voltage in an N channel would be a quarter of the silicon, which is the cleanest way to see what the P channel is costing.
The applications that justify it are the ones where the switch sits in the positive lead of a 48 V system and there is no room for a charge pump: a battery disconnect on a 48 V pack, a reverse polarity block on an industrial input, a high side switch on a telecom rail. In all of those the alternative is three components and a bootstrap, and two P channels in one body is one component.
Key data for the VBA4625
| Configuration | Dual P channel, two independent devices |
| Package | SOP8, surface mount, 1.27 mm pitch |
| VDS | Minus 60 V per device |
| VGS | Plus or minus 20 V |
| Vth | Minus 1.7 V |
| ID | Minus 8.5 A |
| RDS(on) at 4.5 V | 30 milliohm |
| RDS(on) at 10 V | 20 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Body diode | One per channel, forward drop is the loss in a reverse event |
| Thermal path | Eight leads, shared frame |
| Published applications | Power adapters, voltage regulators, general power switching |
Thirty milliohms at 4.5 V from a 60 V P channel
Getting 30 milliohm at 4.5 V out of a 60 V P channel takes a large die, and a large die takes a large gate charge. The two columns, 30 and 20 milliohm, differ by a third, which is a normal spread for this class and tells you the die is not fully enhanced at 4.5 V.
The practical consequence is that a 5 V gate drive gets 30 milliohm and a 10 V gate drive gets 20, and at 6 A those differ by 360 mW per channel. Two channels would differ by 720 mW, which is enough to change the thermal verdict on a sealed enclosure.
A 48 V system has 48 V available for the gate, which is far above the 20 V window, so the gate must be driven through a divider or a clamp whenever the switch is on the high side. A 12 V auxiliary rail, when it exists, is the cleanest source, and it also gives the 10 V column through a resistor and a zener.
Two channels, 8.5 A, and one lead frame
At 20 milliohm and 8.5 A one channel dissipates 1.45 W, and two channels at that current would be 2.9 W in a body with eight leads. Neither is a still air number. The realistic continuous current is 4 to 5 A per channel on a board with a good copper landing, where the total stays under 1 W.
For a battery disconnect the current is often a surge rather than a continuous load, and the die survives a surge because the thermal time constant of the silicon is short. The parameter that decides survival is the safe operating area, which the catalogue page does not publish.
The body diode matters in the reverse polarity case. With the input reversed, the diode of the channel in the positive lead conducts, and the load sees a diode drop rather than a switch. If the requirement is to block the reverse path, the two channels go back to back and the resistance doubles.
The gate clamp for a 48 V high side switch has to handle both the static and the transient case. A resistor divider from the rail to ground sets the on state gate voltage and a zener across the gate and source limits it, and the divider draws current continuously whenever the switch is on. At 48 V a 10 k and 3.3 k pair draws about 3.6 mA, which is 170 mW of standing loss, and that is a real cost in a battery product. A small P channel in the gate path, driven from a logic pin, removes the standing current and is the arrangement most 48 V circuits settle on.
Where it fits
It fits a 48 V battery disconnect, a reverse polarity block on an industrial input, a high side switch on a telecom rail, and a 36 V pack switch with a clamped gate. It does not fit a 60 V rail, and it does not fit a hot swap at 8 A continuous.
Our purchase order follow up page covers what is confirmed on an order and when, which for a large die P channel is worth settling early because the lead time moves more than the price.
The sourcing side of this part is covered on the one stop BOM sourcing. For a large die P channel that arrives with its clamp and driver, that page covers how the group is bought together.
Questions we get on this code
Can the gate be driven from the 48 V rail? Not directly, the window is 20 V. Use a divider, a zener clamp, or a 12 V auxiliary rail.
Is minus 60 V enough for a 48 V pack? A charged 48 V pack is 54 V, so the margin is 6 V. Clamp the input and keep the loop short, or move to an 80 V class part.
Can the two channels be back to back? Yes, and the on resistance doubles to 40 milliohm at 10 V. That is the arrangement for a true block.
What is the reel size? We confirm it on the quotation rather than stating one here.