Contact Us

VBE15R10S

Brand: VBsemi
VBsemi VBE15R10S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE15R10S — Discrete & Power Semiconductors | Superb Automation

VBE15R10S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE15R10S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE15R10S: a 500 V superjunction N channel in TO252

The VBE15R10S is a single N channel MOSFET in TO252 rated at 500 V, plus or minus 30 V on the gate, 10 A of drain current, with a threshold of 3.5 V and 380 milliohm at a 10 V gate. The catalogue names the technology as SJ_Multi-EPI, which means a superjunction structure built by multiple epitaxial growth steps.

Five hundred volts is the class used on a rectified 230 V mains, a 380 V DC bus, and a 400 V battery string. It sits below the 600 to 650 V parts used where the mains can reach 265 V, and above the 200 V parts used on 110 V systems.

The resistance is the number that decides the application. Three hundred and eighty milliohm at 10 A is 38 W of conduction loss, so the part is a 2 to 3 A switch in a DPAK and the rest is headroom for a pulse.

Key data for the VBE15R10S

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS500 V
VGSPlus or minus 30 V
Vth3.5 V
ID10 A
RDS(on) at 10 V380 milliohm
TechnologySuperjunction, multi epitaxial
Body diodeIntrinsic, fast in forward, hard in recovery
Thermal pathDrain tab to copper or heatsink
Gate chargeNot on the catalogue page, low for the voltage class
Typical useOffline flyback, PFC, 400 V load switch
IsolationNone, the tab is the drain

What a superjunction buys at 500 V

A plain planar 500 V die of the same area would have a resistance several times higher, because the drift region that holds the voltage is lightly doped and thick. A superjunction replaces that region with alternating columns of p and n silicon, and when the device is off the columns deplete each other sideways, so the region can be doped far more heavily and still hold the voltage.

The result is a resistance that falls by a factor of three to five at the same voltage and area. The cost is a body diode with a hard recovery, a gate that needs care during a fast dV/dt, and a resistance that climbs faster with temperature than a planar part.

Multi epitaxial growth is one way to build the columns: several thin layers are grown and doped in turn, and the columns form as the layers stack. Deep trench is the other way, where trenches are etched and refilled. The two routes give slightly different charge balance and slightly different diode behaviour.

Three hundred and eighty milliohm in a DPAK

At 380 milliohm and 2 A the loss is 1.5 W, which with 45 degrees per watt is a 68 C rise. At 3 A it is 3.4 W and a 154 C rise, which is too much without a heatsink. So the working current in a board is 1.5 to 2.5 A, and the 10 A rating is a pulse or a case held cold.

In a flyback the switch spends most of its time off and the loss is dominated by switching, not conduction. At 65 kHz with a 500 V bus and a drain current that ramps from zero, the turn off loss can be a few watts on its own, and that is why the part is chosen for its gate charge as much as its resistance.

In a PFC the same part runs at higher current for a shorter duty and the conduction figure matters more. A 380 milliohm part at 2 A RMS is 1.5 W, which a DPAK with a copper plane can pass.

There is one behaviour of a superjunction that catches people out on a 500 V bus: the output capacitance is non linear, and it is large at low drain voltage and small at high voltage. The energy stored in that capacitance is not half C times V squared with a single C, and the loss at turn on is therefore not what a linear calculation gives. In a hard switched converter the difference is a factor of two, and it changes the balance between the switching loss and the conduction loss. The data sheet prints a capacitance curve for exactly this reason, and a converter that is sized from the single capacitance value in the table will run hotter than expected at turn on.

Where the part fits and where it does not

It fits an offline flyback under 30 W, a 400 V bus precharge, a small PFC stage, and a load switch on a 380 V DC bus. It does not fit a bridge or a synchronous rectifier on the secondary, because the body diode recovery is too hard for that duty, and it does not fit a mains input that can reach 265 V without a voltage margin check.

Our component obsolescence management page covers what is done when a 500 V part reaches the end of its life and a superjunction replacement has to be qualified without changing the board.

The sourcing side of this part is covered on the last time buy and LTB planning. For a 500 V part in a long life product, that page covers how the last buy quantity is set before the family ends.

Questions we get on this code

Is 500 V enough for a 230 V mains? A 230 V RMS mains peaks at 325 V, and a flyback adds the reflected voltage plus the leakage spike. Five hundred volts is enough only with a low reflected voltage and a clamp. Most offline converters use 600 or 650 V.

Why is the gate window 30 V rather than 20 V? High voltage parts are often driven through a gate transformer or a bootstrap that can overshoot. The wider window is there for that overshoot, not for a 30 V drive.

What is the avalanche rating? Not published on the catalogue page. Any leakage spike above 500 V has to be clamped externally.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm what is in stock at the time of the request.