VBB1240
Product Specifications
VBB1240
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBB1240 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBB1240: a 20 V N channel in SOT23-3 at 6 A
The VBB1240 is a single N channel MOSFET in a SOT23-3 body with a 20 V drain to source rating, a plus or minus 8 V gate window, a 0.8 V threshold, a 6 A current figure and resistances of 29.6 milliohm at 2.5 V and 26.5 milliohm at 4.5 V.
The gate window is the first thing to notice, because plus or minus 8 V is narrow for a part that is often driven from a 12 V rail. A SOT23-3 part with an 8 V gate limit is a low voltage switch, and the 20 V drain rating agrees: this is a part for 3.3 V, 5 V and 12 V logic rails, not for an automotive input.
Six amps in a SOT23-3 is also a statement. The body is 2.9 by 1.3 mm with three leads, and the die inside is small. The current figure is a die limit and the thermal path is three narrow leads into a small copper landing.
Key data for the VBB1240
| Configuration | Single N channel |
| Package | SOT23-3, surface mount |
| VDS | 20 V |
| VGS | Plus or minus 8 V |
| Vth | 0.8 V |
| ID | 6 A |
| RDS(on) at 2.5 V | 29.6 milliohm |
| RDS(on) at 4.5 V | 26.5 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal path | Three leads, the drain lead carries most of the heat |
| Board area | About 3 square millimetres |
| Typical use | Load switch in a DC-DC converter or a small motor path |
Ten per cent between the two gate columns
29.6 against 26.5 milliohm is a 10 per cent spread, which is as flat as a pair of columns gets. The die is essentially fully enhanced at 2.5 V, and the 0.8 V threshold means a 3.3 V logic pin gives 2.5 V of overdrive.
That makes the part genuinely operable from a microcontroller pin, which is unusual and useful. The caveat is the gate window of plus or minus 8 V: a pin that can be pulled to 12 V, or a rail that rings, will exceed it. The 8 V window is comfortable inside a 5 V system and marginal on a 12 V system.
The 6 A figure at 26.5 milliohm would be 954 mW in a body with three leads. A SOT23-3 on a small landing sits around 150 to 200 degrees per watt junction to ambient, so 954 mW is a 140 to 190 C rise, which is not a working point. At 2 A the loss is 106 mW and the rise 20 C, which is where the part actually lives.
Small body, small copper, and the drain lead
In a SOT23-3 the drain is the single lead on one side, and it is both the thermal path and the current path. That means the copper on the drain pad is the heatsink, and a wide trace under it is worth more than any other change to the board.
The source and gate share the other side, so the gate trace and the source return are close together, which is good for loop inductance and bad for coupling if the gate trace runs parallel to a switching node. At the currents this part handles the coupling is small, and the routing of a few millimetres of trace does not decide the behaviour.
What does decide the behaviour is the load. A SOT23-3 switch driving a capacitive load inrush will see a current spike well above 6 A, and the safe operating area of a small die is short. The pulse has to be limited by a series resistor or by a controlled turn on, and the catalogue page does not give the SOA curve.
In a three lead body the copper under the drain lead is the only thermal lever, and it is worth being generous with it. A 6 by 6 mm pour on the drain side, connected to the plane below by a few vias, takes the junction to ambient resistance from around 200 degrees per watt down to roughly 120, which doubles the current the part can pass for the same rise. That single change is usually worth more than any choice between two parts with 26 and 30 milliohm, because the die is not the limit in this body.
Where it fits
It fits a load switch on a 3.3 V or 5 V rail at 1 to 2 A, a small motor or solenoid driver, a level shifter, an LED string switch, and a battery path switch in a wearable. It does not fit a 12 V rail without a gate clamp, and it does not fit a 6 A continuous load.
Our BOM consolidation page covers how a group of similar lines is reduced, and a SOT23-3 N channel at 20 V is exactly the kind of part that appears six times on one board with four different part numbers.
The sourcing side of this part is covered on the how to reduce component cost. For a 20 V switch that appears several times on one board, that page covers where a lower cost equivalent can be used.
Questions we get on this code
Can it be driven from a 3.3 V pin? Yes. The threshold is 0.8 V and the resistance is essentially flat from 2.5 V, so a 3.3 V pin gives nearly the full performance.
Will it survive a 12 V gate? No. The window is plus or minus 8 V, so a 12 V pull exceeds the rating.
How much current can it really carry? About 2 A continuous on a small landing, more with a wide drain pad. The 6 A figure is a die limit.
Is there a dual version in the same body? Not in SOT23-3, which has three leads. A dual would need a six lead body.