Contact Us

INA2332AIPWT

Brand: Texas Instruments
Texas Instruments INA2332AIPWT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2332AIPWT — Power Management & Signal Chain | Superb Automation

INA2332AIPWT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2332AIPWT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2332AIPWT: the same low cost dual on the small reel, for the pilot build

INA2332AIPWT is the small reel carrier of the low cost dual CMOS instrumentation amplifier, fourteen pin TSSOP, same die and same electrical rows as the large reel code beside it. The small reel exists for the pilot build and the first article run, where a full reel is more parts than the line can consume before the next revision.

Everything that matters electrically is shared with the R suffix: 415 microamps per channel, 2 megahertz at a gain of 25, 5 volts per microsecond, 46 nanovolts per root hertz and the plus or minus 8 millivolt offset window. What differs is only the quantity on the carrier and the feeder setup, which is the one line a production planner actually needs from this page.

INA2332AIPWT as the vendor document publishes it

Channels2
Gain5 V/V internal, up to 1000 V/V with two external resistors
Supply2.7 to 5.5 volts, 2.5 volts operating minimum
Quiescent current415 microamps typical, 490 maximum per channel
Shutdown current0.01 microamps typical
Offset voltage at 5 voltsplus or minus 2 millivolts typical, plus or minus 8 millivolts maximum
Offset voltage over temperatureplus or minus 9 millivolts maximum
Offset drift5 microvolts per degree
Common mode rejection60 decibels minimum, 73 typical
Common mode window at 5 volts0.55 to 3.8 volts
Input bias currentplus or minus 0.5 picoamps typical, plus or minus 10 picoamps maximum
Voltage noise46 nanovolts per root hertz at 1 kilohertz
Gain error0.07 per cent typical, 0.4 per cent maximum
Bandwidth2 megahertz at a gain of 25
Slew rate5 volts per microsecond
Settling time1.7 microseconds to 0.1 per cent on a 2 volt step
Temperature rangeminus 55 to plus 125 degrees
Package14 pins, TSSOP body PW
Catalogue codeINA2332AIPWT
Vendor statusactive
Carriersmall reel, T suffix
Package14 pins, TSSOP body PW
Moisture levellevel 2, 260 degrees, one year floor life

A gain of five in a fourteen pin TSSOP, and what the second channel shares

INA2332AIPWT is the dual channel half of the low cost CMOS instrumentation amplifier family, in a fourteen pin TSSOP, with a trimmed internal gain of five and a pair of external resistors for anything above it. The internal network is a 10 kilo-ohm and a 40 kilo-ohm pair, so the law reads five plus five times the ratio of the two resistors, and the same two resistors set both channels.

The supply window is 2.7 to 5.5 volts, the output swings to within 25 millivolts of each rail at a gain of ten or above, and the temperature range is minus 55 to plus 125 degrees. The pair is aimed at a two channel bridge instrument and a two sensor front end rather than at a precision bench instrument, and the electrical table says so in the offset row.

Sixty decibels of rejection, and the window it is measured over

The common mode rejection of INA2332AIPWT is 60 decibels minimum and 73 typical, and it is quoted over a common mode window of 0.55 to 3.8 volts on a five volt supply. On a 2.7 volt supply the window narrows to 0.35 to 1.5 volts and the rejection figure stays at the same 60 decibels minimum.

A 73 decibel part rejects a 1 volt common mode shift to about 220 microvolts referred to the input, which is small against the 8 millivolt offset but not against the 250 microvolt offset of the trimmed part. That is why the low cost member of the family is normally used with a sensor that sits mid rail and does not move, and why a long cable with a moving ground is a poor match for it.

Eight millivolts of offset is the trade this part makes

The offset of INA2332AIPWT is quoted at plus or minus 2 millivolts typical and plus or minus 8 millivolts maximum on a five volt supply, and plus or minus 9 millivolts maximum over the full temperature window. The drift is 5 microvolts per degree typical, so a channel trimmed at 25 degrees and run at 85 degrees adds 300 microvolts on top of the room figure.

That row is the whole selection argument. A 10 millivolt full scale bridge with 8 millivolts of offset is 80 per cent of full scale before any gain is applied, so the part only works where either the span is larger than a volt or a calibration step is part of the process. The same body with a laser trimmed front end is published at 250 microvolts, and the price difference between the two is the price of that calibration.

The carriers, the moisture level, and the marking

The dual body is published in the fourteen pin TSSOP on two reel sizes: the R suffix is the large reel and the T suffix is the small reel. Both are moisture level 2 at 260 degrees with a one year floor life and a nickel palladium gold finish, so the handling rule does not change when a build moves from one reel size to the other.

The single channel member of the family sits in an eight pin MSOP, which is a different body with a different footprint, so a board that starts on the single and grows to the dual needs the fourteen pin land pattern from the beginning rather than a rework at the prototype stage.

Four hundred and fifteen microamps, and a shutdown pin that gives it back

Each channel of INA2332AIPWT draws 415 microamps typical and 490 microamps maximum, and the pair drops to 0.01 microamps with the shutdown pin pulled below 0.8 volts. The return takes microseconds, which is fast enough to power the front end per reading rather than leaving it running, and that is the case the shutdown pin was put on the package for.

The bandwidth is 2 megahertz at a gain of 25 with a slew rate of 5 volts per microsecond, the voltage noise is 46 nanovolts per root hertz at 1 kilohertz, and the settling time to 0.1 per cent on a 2 volt step is 1.7 microseconds. Those three rows are what allow the part to drive a sampling converter directly rather than through a buffer.

Where a five volt per volt dual belongs, and where it does not

INA2332AIPWT belongs in a two channel load cell instrument, a dual thermocouple input with cold junction compensation, a two axis strain gauge, and a handheld meter that reads two sensors through one package. The gain of five floor is no limitation for a bridge, which rarely produces more than tens of millivolts at full scale.

It does not belong where the offset budget is under a millivolt, where the common mode runs above 3.8 volts on a five volt supply, or where the sensor is a current shunt sitting on a 24 volt rail. Those three cases are the current sense family and the trimmed instrumentation family, both of which carry their own offset and common mode rows.

What the eight millivolt row does to a process

The offset row on this part is a process question rather than an amplifier question. A two point trim at the working temperature costs a fixture and a few seconds per board, and it recovers the offset but not the 20 microvolts per degree maximum drift, so a channel calibrated at 25 degrees and run at 85 degrees still moves 1.2 millivolts.

The alternative is to buy the trimmed member of the same family, which carries 250 microvolts instead of 8 millivolts in the same fourteen pin body. The difference in unit price is normally smaller than the cost of the trim station, which is why the low cost code is used on boards that are calibrated anyway rather than on boards that are calibrated because of it.

The small reel is a pilot build decision rather than a price decision. Our BOM scrubbing page covers the gain resistors against the bill of materials, and the vendor consolidation page covers holding one carrier across builds.

Can the small reel feed a production line? It can, but the reel change interval is shorter and a line that runs more than a few thousand boards a week will spend more time loading than building. The large reel code is the one to use once the board is fixed.

Is the part number printed on the reel the same as the order code? The order code carries the T suffix and the marking on the body does not, so the traceability check has to read the reel label rather than the laser mark.