Contact Us

INA2331AIPWT

Brand: Texas Instruments
Texas Instruments INA2331AIPWT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2331AIPWT — Power Management & Signal Chain | Superb Automation

INA2331AIPWT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2331AIPWT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2331AIPWT: the same dual five volts per volt part on the small reel, with the last time buy flag on the code

INA2331AIPWT is the dual channel CMOS instrumentation amplifier in the fourteen pin TSSOP on the small reel, the carrier the vendor publishes with the T suffix. The electrical rows are the ones the family is known for: a trimmed internal gain of five, 250 microvolts of offset on the A grade, 94 decibels of rejection, 0.5 picoamps of bias current, 2 megahertz at a gain of 25 and 415 microamps per channel.

The reason this page exists separately is the status line. The vendor addendum prints this code as a last time buy, which means the small reel is the carrier that runs out first while the large reel code continues. A line that buys the T suffix for a pilot build and then moves to the R suffix for production is making a documented move between two carriers of the same die, not a change of part.

INA2331AIPWT as the vendor document publishes it

Channels2
Gain5 V/V internal, up to 1000 V/V with two external resistors
Supply2.7 to 5.5 volts, 2.5 volts operating minimum
Quiescent current415 microamps typical, 490 maximum per channel
Shutdown current0.01 microamps typical
Offset voltageplus or minus 250 microvolts maximum on the A grade
Offset drift5 microvolts per degree
Common mode rejection90 decibels minimum, 94 typical at a 5 volt supply
Input bias current0.5 picoamps typical
Voltage noise46 nanovolts per root hertz at 1 kilohertz
Bandwidth2 megahertz at a gain of 25
Slew rate5 volts per microsecond
Output swingwithin 20 millivolts of each rail at a gain of 10 or above
Temperature rangeminus 55 to plus 125 degrees
Package14 pins, TSSOP body PW
Catalogue codeINA2331AIPWT
Vendor statuslast time buy on this reel code
Carriersmall reel, T suffix
Package14 pins, TSSOP body PW
Moisture levellevel 2, 260 degrees, one year floor life
GradeA, 250 microvolts maximum offset

The dual of the five volt per volt CMOS part

INA2331AIPWT is the dual channel version of the rail to rail output CMOS instrumentation amplifier that carries a trimmed internal gain of 5, in a 14 pin TSSOP rather than the 8 pin package of the single. The internal network is a 10 kilo-ohm and a 40 kilo-ohm pair, and any gain above 5 comes from one external resistor pair as 5 plus 5 times their ratio, up to about 1000.

The 5 volt per volt floor and the 2.7 to 5.5 volt supply are shared with the single, so a board that needs two channels of the same front end can use one package and one calibration table. The two channels are independent apart from the supply and the shutdown pin, and the crosstalk between them is 114 dB, which is low enough that one channel can run at a gain of 100 while the other sits at 5.

One millivolt of offset on the A grade, and the temperature window

The offset of INA2331AIPWT is quoted at 250 microvolts typical with 1 millivolt maximum on the A grade, and 1.7 millivolts over the full temperature range. The drift is 5 microvolts per degree, so a channel that calibrates at 25 degrees and runs at 85 adds 300 microvolts on top of whatever the room temperature sort gave.

That gap is the honest cost of a CMOS input stage without a chopper. The long term stability row is 0.4 microvolts per month, which is smaller than the temperature term by an order of magnitude, so the calibration interval is set by temperature rather than by ageing. A channel whose full scale is 2 volts sees 1 millivolt as 0.05 per cent, and a channel at 20 millivolts sees it as 5 per cent.

Ninety four decibels at DC, fifty at forty five kilohertz

The common mode rejection of INA2331AIPWT is 90 dB minimum and 94 dB typical at a 5 volt supply over the 0.55 to 3.8 volt window, and the family description keeps 50 dB of rejection up to 45 kilohertz. On a 2.7 volt supply the window narrows to 0.35 to 1.5 volts and the rejection holds at 94 dB, with 72 dB minimum over temperature.

The 45 kilohertz figure is the one that decides a real installation. A front end next to a switching supply sees its common mode at the switching frequency, and 50 dB turns a 1 volt common mode into 3 millivolts at the input, which is larger than the offset. A 1 kilo-ohm series resistor ahead of the part adds a pole against the 3 picofarads of input capacitance without loading a low impedance source, and the 10 to the 13 ohms of input impedance means the resistor does not create an offset of its own.

Four hundred and fifteen microamps, and one hundredth of a microamp asleep

Each channel of INA2331AIPWT draws 415 microamps typical and 490 maximum, and the pair draws 0.01 microamps with the shutdown pin pulled low. The return from shutdown takes microseconds, which is fast enough to power the front end per reading rather than leaving it running: a logger that measures once a second for 2 milliseconds spends a fifth of one per cent of its life in measurement and the rest asleep.

The shutdown is common to both channels, so a dual used for two sensors is either awake for both or asleep for both, which is a wiring decision rather than a software one. The 490 microamp ceiling per channel is the number to carry in a battery budget, and it is the largest single term in a small instrument that has no display backlight.

Two megahertz at a gain of twenty five, and twenty millivolts of headroom

The bandwidth of INA2331AIPWT is 2 megahertz at a gain of 25, with a slew rate of 5 volts per microsecond and a voltage noise of 46 nanovolts per root hertz at 1 kilohertz. The output reaches within 20 millivolts of each rail only at a gain of 10 or above, so a low gain channel loses the top and bottom of a converter range.

On a 12 bit converter with a 4.096 volt reference, one bit is 1 millivolt, so 20 millivolts of headroom is 20 codes at each end and a channel that uses the whole range has to accept it. The 2 megahertz is what lets the part drive a sampling converter directly: at a gain of 25 it settles inside the acquisition window of a converter running at a few hundred kilo-samples per second, and at a gain of 1000 it is a few kilohertz wide and the settling time dominates a scan.

Where the dual five volt per volt part belongs

INA2331AIPWT belongs in a two channel bridge instrument, a dual thermocouple input with cold junction compensation, a two axis strain gauge, and a handheld meter that reads two sensors through one package. The 5 volt per volt floor is not a limitation for a bridge, which rarely produces more than tens of millivolts, and the 415 microamps is what a battery instrument can afford.

It does not belong where the signal needs unity gain, because the minimum is 5. It does not belong on a single alkaline cell without a boost, because the floor is 2.7 volts. It does not belong on a high side sense above its own rail, because the common mode window stops 1.2 volts below the positive rail. And it does not belong in a channel that has to hold 100 microvolts, which is the chopper class. Our amplifier cross reference page covers the single, dual and chopper parts on one table, and the BOM scrubbing page covers the gain pair against the bill of materials.

The carrier change is the item to settle before the last time buy window closes. Our last time buy planning page covers the quantity calculation, and the amplifier cross reference page covers what else sits in this family.

Is the T suffix a different die from the R suffix? No. Both codes are the same fourteen pin TSSOP body with the same electrical rows, and only the reel size differs, which is why a production move between them needs no board change.

What does last time buy mean on this code? The vendor addendum prints the status as last time buy, so the remaining stock is finite. A buyer either takes the small reel now or moves to the large reel code, and the second option is normally the cheaper one per unit.