Contact Us

INA2180A1IDGKT

Brand: Texas Instruments
Texas Instruments INA2180A1IDGKT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2180A1IDGKT — Power Management & Signal Chain | Superb Automation

INA2180A1IDGKT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2180A1IDGKT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2180A1IDGKT: the 250 piece reel code, printed as obsolete in the current addendum

INA2180A1IDGKT is the small reel code for the dual gain of twenty current sense amplifier in the eight pin VSSOP, and the vendor addendum dated for this catalogue prints it as obsolete, with no quantity, no finish and no moisture level. The part it names is the same die as the 2500 piece reel beside it, so the electrical rows are unchanged.

That status is the reason this page exists rather than a stock note. A buyer who needs 250 pieces cannot order the T code from the vendor any more, and the practical routes are a cut reel of INA2180A1IDGKR or stock that a distributor already holds. The gain of 20, the 26 volt common mode window, the 350 kilohertz and the 355 microamps are the same on both codes.

INA2180A1IDGKT as the vendor document publishes it

Channels2
Gain20 V/V, the A1 member of the family
Supply2.7 to 5.5 volts
Common mode rangeminus 0.2 to 26 volts
Quiescent current355 microamps typical, 500 maximum for both channels, 520 over temperature
Offset at zero common mode25 microvolts typical, 150 maximum
Offset over the full range100 microvolts typical, 500 maximum
Offset drift0.2 microvolts per degree typical, 1 maximum
Rejection84 minimum, 100 typical decibels
Power supply rejection8 microvolts per volt typical, 40 maximum
Gain error0.1 typical, 1 maximum per cent
Gain drift1.5 parts per million per degree typical, 20 maximum
Nonlinearity0.01 per cent between 0.5 volts and 0.5 volts below the supply
Voltage noise40 nanovolts per root hertz
Bandwidth and slew350 kilohertz, 2 volts per microsecond
Output swingwithin 20 millivolts of the supply, 8 milliamps maximum
Temperature rangeminus 40 to plus 125 degrees
Vendor statusobsolete in the current addendum
Catalogue codeINA2180A1IDGKT
Carriersmall reel of 250, no longer published
Lead finishprinted as a call to the vendor on this row
Catalogue notethe 2500 piece reel code is the active carrier

The carrier rows, and the one code that is no longer produced

The dual channel part in the eight pin VSSOP is published on a 2500 piece large reel as INA2180A1IDGKR, with the marking 1CX6, a nickel palladium gold finish, moisture level 2 at 260 degrees with a one year floor life, and a temperature range of minus 40 to plus 125 degrees. The small reel code INA2180A1IDGKT is printed as obsolete in the same addendum, with no quantity and no finish.

That is a catalogue issue rather than a technical one. A buyer who needs 250 pieces has to take a partial reel of the R code or find stock, because the T code is no longer produced. The single channel and four channel members of the family are unaffected, and the electrical rows are identical across the three, so a board that has to change channel count keeps its calibration.

A gain of twenty, and a common mode that goes above the supply

INA2180A1IDGKT is a dual current sense amplifier with a fixed gain of 20, which is the A1 member of a family that also offers 50, 100 and 200. The inputs accept a common mode from 0.2 volts below ground to 26 volts, on a supply of 2.7 to 5.5 volts, so the part measures a shunt on a 24 volt rail while running from a 3.3 volt logic rail.

That window is the whole point of the family. A current sense amplifier that only works inside its own supply needs a separate higher rail or a level shift, and the 26 volt window removes both. The gain of 20 suits a 10 milliohm shunt at 5 amps, which gives 50 millivolts of signal and 1 volt at the output, and the four gain options let the same board cover a 0.5 amp and a 20 amp channel with one part number.

One hundred and fifty microvolts at zero common mode, five hundred across the range

The offset of INA2180A1IDGKT is 25 microvolts typical and 150 maximum when the common mode sits at zero volts, and 100 typical with 500 maximum over the full zero to 26 volt window at a 10 millivolt sense voltage. The drift is 0.2 microvolts per degree typical and 1 maximum, and the power supply rejection is 8 microvolts per volt typical against 40 maximum.

Read at the shunt, 500 microvolts divided by a gain of 20 is 25 microvolts of input error, and on a 10 milliohm shunt that is 2.5 milliamps of current error. On a 1 milliohm shunt it is 25 milliamps, which is why the family is offered in four gains: the error is set by the sense voltage, so a smaller shunt needs a higher gain rather than a better amplifier. The offset is specified by extrapolation to zero sense voltage, which is the honest way to quote a current sense part.

Three hundred and fifty kilohertz, and three hundred and fifty five microamps for two channels

The bandwidth of INA2180A1IDGKT is 350 kilohertz, the highest of the four gain options, with a slew rate of 2 volts per microsecond and a nonlinearity of 0.01 per cent between 0.5 volts and 0.5 volts below the supply. The quiescent current is 355 microamps typical and 500 maximum for both channels, rising to 520 microamps maximum over temperature.

Those two rows are why the part is used in a battery product. Two channels of current sense for half a milliamp is a fraction of what a controller with an integrated sense amplifier draws, and 350 kilohertz is enough to follow a motor current through a pulse width modulated cycle at 20 kilohertz with 17 samples per period. The output stage swings to within 20 millivolts of the supply and to within 0.5 millivolts of ground into 10 kilo-ohms.

Eighty four decibels of rejection, measured where the part is used

The common mode rejection of INA2180A1IDGKT is 84 dB minimum and 100 dB typical, and it is specified over the full zero to 26 volt common mode at a 10 millivolt sense voltage across the whole minus 40 to plus 125 degree range rather than at room temperature alone. The gain error is 0.1 per cent typical and 1 per cent maximum, with a gain drift of 1.5 parts per million per degree typical and 20 maximum.

The rejection figure is the one that decides whether the part can sit on a switching node. A 24 volt rail that swings 1 volt at 100 kilohertz puts that volt on both inputs, and 84 dB turns it into 63 microvolts at the input, which is 1.3 millivolts at the output of a gain of 20 stage. The 1 per cent gain error is larger than that on a 1 volt output, so a channel that needs absolute accuracy trims the gain rather than the offset.

Where a gain of twenty current sense belongs

INA2180A1IDGKT belongs on a 12 or 24 volt rail with a 10 milliohm shunt and a 5 amp load, in a battery charger, a motor drive, a hot swap card, a power over ethernet port and a server supply. The 26 volt common mode, the 350 kilohertz bandwidth and the 355 microamps are the three rows that fit those cases, and the dual channel covers a positive and a negative rail in one package.

It does not belong on a rail above 26 volts, where the input window ends even though the part would survive. It does not belong on a shunt below 1 milliohm without accepting milliamps of error, because the offset is fixed and the gain is fixed. It does not belong in a bidirectional measurement that needs a signed output, because the output is unipolar. Our amplifier cross reference page covers the four gain options, and the BOM scrubbing page covers the shunt and the gain against the bill of materials.

Availability rather than price decides this code. Our vendor consolidation page covers the move to the large reel, and the traceability report page covers the label on a cut reel.

Is the T code still produced? The addendum prints it as obsolete, with no quantity and no finish, so it should be treated as end of life.

What replaces it? The 2500 piece reel INA2180A1IDGKR, either as a full reel or as a cut length from a distributor.